সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

তৈরি করেছেন

Woody

4. নভেম্বর 2026NO
১১
০
০
০
০

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
মধ্যবর্তী
Unknown

নির্দেশাবলি

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা4 built-up pulleys

প্রয়োজনীয় সরঞ্জাম:

কাঠের লেদকাঠের লেদ
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

এই ধাপের উপকরণ:

ইস্পাতের পাইপ (পুরু দেয়াল, প্যাঁচকাটা প্রান্ত)ইস্পাতের পাইপ (পুরু দেয়াল, প্যাঁচকাটা প্রান্ত)3 shafts
অজানা ধাতুঅজানা ধাতু1 babbitt bushings
পাইন কাঠপাইন কাঠ1 frame

প্রয়োজনীয় সরঞ্জাম:

ধাতুর উকোধাতুর উকো
ছিদ্রযুক্ত ঝাঁঝরি-চামচছিদ্রযুক্ত ঝাঁঝরি-চামচ
হাত-করাতহাত-করাত
হাতুড়িহাতুড়ি
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

এই ধাপের উপকরণ:

শিরিষ কাগজশিরিষ কাগজ1 6 in garnet paper
সুতির কাপড়সুতির কাপড়1 টুকরা
পশু আঠাপশু আঠা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

সি-আকৃতির ক্ল্যাম্পসি-আকৃতির ক্ল্যাম্প
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

এই ধাপের উপকরণ:

পাইন কাঠপাইন কাঠ1 platform, float

প্রয়োজনীয় সরঞ্জাম:

কাঠের লেদকাঠের লেদ

উপকরণ

7

প্রয়োজনীয় সরঞ্জাম

6

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...