সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge.
Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large.
Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
মধ্যবর্তী
Unknown
নির্দেশাবলি
1
1
Braze the gas inlet
Braze the gas inlet
Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.
এই ধাপের উপকরণ:
পিতলের নল1 body and side tube
অজানা ধাতু1 brazing metal and spike
সোহাগার গুঁড়ো1 brazing fluxপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
কামারের ভাটি2
2
Fit the glass air jet
Fit the glass air jet
Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.
এই ধাপের উপকরণ:
কাচের নল3 air jets of several sizes
কর্ক1 jet corkপ্রয়োজনীয় সরঞ্জাম:
বুনসেন বার্নার3
3
Set up the bench
Set up the bench
Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.
এই ধাপের উপকরণ:
নরম ইস্পাতের পাত1 bench cover
কঠিন কাঠের চাঁই1 mounting block
অজানা ভালভ2 gas and air taps
রাবারের নল1 flexible tubesপ্রয়োজনীয় সরঞ্জাম:
স্তম্ভযুক্ত তুরপুন যন্ত্র4
4
Light it and blow
Light it and blow
Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.
প্রয়োজনীয় সরঞ্জাম:
হাপরউপকরণ
9- 1 body and side tubeপ্লেসহোল্ডার
- 1 brazing metal and spikeপ্লেসহোল্ডার
- 1 brazing fluxপ্লেসহোল্ডার
- 3 air jets of several sizesপ্লেসহোল্ডার
- 1 jet corkপ্লেসহোল্ডার
- 1 bench coverপ্লেসহোল্ডার
- 1 mounting blockপ্লেসহোল্ডার
- 2 gas and air tapsপ্লেসহোল্ডার
- 1 flexible tubesপ্লেসহোল্ডার
প্রয়োজনীয় সরঞ্জাম
5- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
সংযুক্ত ব্লুপ্রিন্টের উপাদান

10% স্বীকৃতি
Venetian Borax: Refining Tincal with Lime
Charlie দ্বারা
অজৈব
২২
০
০
০
১
০

10% স্বীকৃতি
Natural Rubber Tubing, Bands and Sheet: Sulfur-Cured with Heat
Mary দ্বারা
রসায়ন
১৬
০
০
০
২
০

10% স্বীকৃতি
Oak Boards and Blocks, Milled and Air-Dried
Woody দ্বারা
কাঠের কাজ
৪৬
০
০
০
৩
০

10% স্বীকৃতি
Building a Box Bellows — The Breath That Makes Metal Obey Fire
Emma দ্বারা
কাঠের কাজ
১০৯
০
০
০
৮
০
এই ব্লুপ্রিন্ট যা তৈরি করে
CC0 পাবলিক ডোমেন
এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।
মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।
