সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)
Forge

তৈরি করেছেন

Forge

15. নভেম্বর 2026NO
৬
০
০
০
০

Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)

Eli Whitney Blake's jaw breaker (patented 1858), the standard first crusher of the ore mill, as Robert Richards described it: a ribbed cast frame on four legs, a fixed jaw bedded in zinc, a steel swing jaw hung from a shaft at the top, and an eccentric that lifts a pitman to straighten two toggles and push the jaw shut; rubber springs pull it back. A wedge sets the gap; a heavy flywheel carries it through each half-turn of crushing.
উন্নত
Weeks (castings and machining)

নির্দেশাবলি

1

Sizes and power

Jupyter নোটবুক লোড হচ্ছে…
2

Read Richards

"As the eccentric lifts the pitman, it straightens out the toggles, lengthening the distance between their outer ends. This forces the swing jaw to approach the fixed jaw, crushing the rock."
3

Frame and fixed jaw

Cast the frame of strong, ribbed cast iron or cast steel, with four legs bolted down, bearing boxes on top for the swing-jaw shaft and the eccentric shaft, and a horizontal web at the rear for the toggle block and wedge. Bed the fixed jaw against the frame end with 1/4 in. (6 mm) of zinc, and hold its jaw plate with two wedge-shaped cheek plates driven into recesses in the frame.

এই ধাপের উপকরণ:

ঢালাই লোহার জিনিসঢালাই লোহার জিনিস1 টুকরা
দস্তার বাটদস্তার বাট1 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ঢালাইয়ের হাতাঢালাইয়ের হাতা
যৌগিক কপিকলযৌগিক কপিকল
হাতুড়িহাতুড়ি
4

Swing jaw

Make the swing jaw of steel, fixed to its shaft by a gib and key bolt, with its jaw plate held by dovetails, a steel toggle bearing at the back and an eye near the bottom for the spring rod. Jaw plates: chilled cast iron with lengthwise 90° corrugations.

এই ধাপের উপকরণ:

ঢালাই লোহার জিনিসঢালাই লোহার জিনিস1 টুকরা
ইস্পাতের শ্যাফটইস্পাতের শ্যাফট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
রেঞ্চের সেটরেঞ্চের সেট
5

Pitman, toggles and wedge

Hang a strong steel pitman from the eccentric shaft on babbitt bearings taken up by a key. Fit two toggles: one between the toggle block and the pitman, one between the pitman and the swing jaw, all four toggle bearings steel, held by set screws. Set the toggle block on its bolt against the wedge, which an adjusting bolt raises or lowers.

এই ধাপের উপকরণ:

ইস্পাতের শ্যাফটইস্পাতের শ্যাফট1 টুকরা
অজানা ধাতুঅজানা ধাতু1 টুকরা
ঢালাই লোহার জিনিসঢালাই লোহার জিনিস1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
রেঞ্চের সেটরেঞ্চের সেট
6

Springs, flywheel and drive

Fit two spring rods from the swing jaw through rubber springs held in compression against a spring bar. Key a heavy flywheel to the eccentric shaft and bolt the drive pulley to it; plug all oil holes against grit and shield the boxes and toggles with the half hopper. Drive it by belt (Table 5: 275 rev./min).

এই ধাপের উপকরণ:

প্রাকৃতিক রবারের পাতপ্রাকৃতিক রবারের পাত1 টুকরা
ঢালাই লোহার জিনিসঢালাই লোহার জিনিস1 টুকরা
কপিকলকপিকল1 টুকরা
ড্রাইভ বেল্টড্রাইভ বেল্ট1 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

রেঞ্চের সেটরেঞ্চের সেট
ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
7

Run and adjust

Feed rock by hand, shovel or chute into the mouth. As the jaw plates wear and the product gets coarse, raise the wedge by its nut; when that is used up, fit longer toggles that keep the pitman vertical; then turn the jaw plates end for end; last, fit new plates.

প্রয়োজনীয় সরঞ্জাম:

রেঞ্চের সেটরেঞ্চের সেট
8

Troubleshooting

Jaw breaker troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter II, §§ 11-14, pp. 13-17, Figs. 5-8 and Table 5 (checked on the archive.org scan oredressing01richuoft; p. 15 from its text layer). Blake's first 1858 form gave the most movement at the mouth; he soon reversed it so the bottom of the jaw moves most. Richards describes a bought Farrel or Fraser & Chalmers machine: building it from castings and metric figures are ours, and the babbitt alloy has no head yet.

উপকরণ

8

প্রয়োজনীয় সরঞ্জাম

5

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...