সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Ice Boat: Crossed Timbers, Skate-Edged Runners, Bicycle-Fork Steering and a Gaff Sail (Boy Mechanic, 1915)
Woody

তৈরি করেছেন

Woody

13. নভেম্বর 2026NO
৬
০
০
০
০

Ice Boat: Crossed Timbers, Skate-Edged Runners, Bicycle-Fork Steering and a Gaff Sail (Boy Mechanic, 1915)

Robert K. Patterson's ice boat from The Boy Mechanic, Book 2 (1915): a 16 ft timber crossed by a 10-1/2 ft one and braced with wires, two front runners of band iron ground like a skate edge, and a rear steering runner clamped in a cut-down bicycle fork worked by a lever. His text and his drawing differ on the mast (about 12 ft against 14 ft); both are given.
উন্নত
About 1 week

নির্দেশাবলি

1

Text against drawing

Jupyter নোটবুক লোড হচ্ছে…
2

Read The Boy Mechanic, Book 2

"In constructing the ice boat, use two poles, or timbers, one 16 ft. and the other 10-1/2 ft. long, crossed at a point 2-1/2 ft. from one end of the longer timber. The crossed pieces are firmly braced with wires, as shown."
3

Cross and brace the frame

Cross the 10-1/2 ft timber over the 16 ft one, 2-1/2 ft from its front end, and fasten them firmly. Brace them with wires as in the drawing: from the bow to points on the cross timber, and from the cross timber back along the long one. The drawing puts the wire points 6 in and 1 ft 6 in from each end of the cross timber.

এই ধাপের উপকরণ:

কাঠের খুঁটিকাঠের খুঁটি2 টুকরা
গোল মাথার বোল্টগোল মাথার বোল্ট1 টুকরা
ইস্পাতের তারইস্পাতের তার1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
ফিতা-মাপফিতা-মাপ
পেনসিলপেনসিল
4

Make the front runners

Cut two band-iron strips 18 in long, 3 in wide and 1/8 in thick; grind one edge like the edge of a skate and round the ends. Bolt each to the side of a wood piece 18 in long, 6 in wide and 2 in thick, so the ground edge projects about 1 in. With a pole frame, bolt each runner block at right angles to a 12 in piece of wood shaped as drawn, the bolts running diagonally through its shouldered part; the pole end rests on this and is bolted down. With squared timbers, fasten the runners straight to them.

এই ধাপের উপকরণ:

নরম ইস্পাতের চ্যাপ্টা পাটানরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
গোল মাথার বোল্টগোল মাথার বোল্ট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হ্যাকসহ্যাকস
টেবিল ঘষাই যন্ত্রটেবিল ঘষাই যন্ত্র
বেঞ্চ ভাইসবেঞ্চ ভাইস
হাত-ড্রিলহাত-ড্রিল
হাত-করাতহাত-করাত
5

Make the steering runner

Fasten the rear runner between two pieces of wood so its edge projects, and clamp it in a bicycle fork cut down to leave about 3 in of the blades. Bore a hole through the rear end of the long timber for the fork head. Fit a lever (5 ft on the drawing) to the top of the fork head: bore a hole through the lever end at a slight angle to fit the head, slot the end, bore across the width of the handle and put in a bolt as a clamp.

এই ধাপের উপকরণ:

নরম ইস্পাতের চ্যাপ্টা পাটানরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
সাইকেলের ফর্কসাইকেলের ফর্ক1 টুকরা
গোল মাথার বোল্টগোল মাথার বোল্ট1 টুকরা
নরম কাঠের ব্যাটেননরম কাঠের ব্যাটেন1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হ্যাকসহ্যাকস
টেবিল ঘষাই যন্ত্রটেবিল ঘষাই যন্ত্র
হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
হাত-করাতহাত-করাত
বাটালিবাটালি
6

Step the mast and fit the seat

Cut a mortise in the long timber 15 in from the front end and set the mast in it; stay it with wires as drawn. His text says the mast should be about 12 ft; his drawing marks it 14 ft 0 in: choose one and keep the sail to suit. Fasten a board on two crosspieces mortised into the top of the long timber, as a seat for the driver (5 ft long on the drawing, ending 2 ft 3 in from the stern).

এই ধাপের উপকরণ:

নরম কাঠের ব্যাটেননরম কাঠের ব্যাটেন1 টুকরা
ইস্পাতের তারইস্পাতের তার1 টুকরা
পাইন কাঠের তক্তাপাইন কাঠের তক্তা1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
বাটালিবাটালি
রান্দারান্দা
ফিতা-মাপফিতা-মাপ
7

Make and rig the sail

Make the sail of any good material to his drawing: luff (along the mast) 9 ft 0 in, head 4 ft 8 in, foot 11 ft 0 in, leech 12 ft 6 in. Hang the main boom, 11-1/2 ft long, and the upper spar on the mast "in the usual manner". The text also names a jib boom of about 6 ft, which the drawing does not show.

এই ধাপের উপকরণ:

ক্যানভাস কাপড়ক্যানভাস কাপড়1 টুকরা
নরম কাঠের ব্যাটেননরম কাঠের ব্যাটেন1 টুকরা
সুতির রশিসুতির রশি1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

কাঁচিকাঁচি
হাত-করাতহাত-করাত
ফিতা-মাপফিতা-মাপ
8

Troubleshooting

Ice boat troubleshooting.

Flow

Loading...
9

History and honest limits

From "An Ice Boat and Catamaran" by Robert K. Patterson, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 27-28). His text and drawing differ on the mast (about 12 ft against 14 ft 0 in) and on the jib boom, which is in the text only; both are stated, not resolved. He gives no timber sections, wire size or sail cloth: those choices are ours, as are the tools and metric figures. The summer catamaran conversion is not made here.

উপকরণ

11

প্রয়োজনীয় সরঞ্জাম

11
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • 1 vendor sell this, none ship to you yet
    প্লেসহোল্ডার
  • 1 vendor sell this, none ship to you yet
    প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...