সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Reed Basket on a Wood Bottom: 24 Spokes, Rolled Edge, Triple Weave and Break-Down Border (Boy Mechanic, 1915)
Woody

তৈরি করেছেন

Woody

13. নভেম্বর 2026NO
৮
০
০
০
০

Reed Basket on a Wood Bottom: 24 Spokes, Rolled Edge, Triple Weave and Break-Down Border (Boy Mechanic, 1915)

The first lesson of Chas. M. Miller's reed-furniture series in The Boy Mechanic, Book 2 (1915): a basket 5 in across and 3 in high, woven on a bored basswood bottom. The spoke ends are turned into a roll that hides the wooden edge, the side is triple-woven, and the top is finished with a break-down border.
শিক্ষানবিশ
About 3 hours

নির্দেশাবলি

1

His sizes, and the spoke spacing

Jupyter নোটবুক লোড হচ্ছে…
2

Read The Boy Mechanic, Book 2

"The center is the most difficult part of the basket making, and it is best to begin with wood bottoms." The reeds placed vertically are called spokes, the horizontal ones weavers.
3

Make the bottom

On a board about 6 in square, 1/4 in thick (basswood is best, pine or cedar will do), draw the diagonals and two circles from their crossing, 5 in and 4-3/4 in across. Step off 24 points on the inner circle with the compass set about 5/8 in apart, adjusting until they come out even. Bore 1/8 in holes just inside the inner circle at the points, then saw out the 5 in circle (bore first, or the disk may split).

এই ধাপের উপকরণ:

পাইন কাঠের তক্তাপাইন কাঠের তক্তা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

দিকনির্ণয় যন্ত্রদিকনির্ণয় যন্ত্র
পেনসিলপেনসিল
হাত-ড্রিলহাত-ড্রিল
কোপিং করাতকোপিং করাত
4

Set the spokes and roll the edge

Push dry No. 4 reed spokes through the holes, about 5-1/2 in projecting below. Soak bottom and spokes about 15 minutes. Bend each spoke below the bottom down behind the two nearest spokes and out between the third and fourth; force the last two under the first two, making a pinwheel. Then bend them up across the edge of the wood, in front of three spokes and behind the fourth, inserting a short spoke about 4 in long in front of each first so the doubles cover the edge; press them flat and trim any that are too long.

এই ধাপের উপকরণ:

বেতবেত1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

২০ লিটারের বালতি২০ লিটারের বালতি
চামড়া কাটার ছুরিচামড়া কাটার ছুরি
বাটালিবাটালি
5

Triple-weave the side

Put in three soaked No. 3 reed weavers between spokes A-B, B-C and C-D. Each time take the weaver farthest behind in front of the two nearest spokes, behind the third and out in front of the next two. Use weavers no longer than 8 ft; when one runs out, press it back a little and push a new reed in about 1-1/2 in. Press every throw down, and weave to 3 in high.

এই ধাপের উপকরণ:

বেতবেত1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

২০ লিটারের বালতি২০ লিটারের বালতি
চামড়া কাটার ছুরিচামড়া কাটার ছুরি
6

Make the border

Break-down-tight border: bend spoke A behind B and out between B and C, B behind C, and so on to E; then lay the end of A over B to E, in front of F, behind G and out between G and H, and bring F down behind A's end; continue round, leaving the first ends loose so the last spokes can be worked under them. Or use the simple break-down: each spoke behind the next, in front of the one after, and behind the next, not out again.

প্রয়োজনীয় সরঞ্জাম:

চামড়া কাটার ছুরিচামড়া কাটার ছুরি
7

Finish

When dry, cut the long ends off close with a knife, without cutting a weaver. Singe off hairy fibres over a flame that will not smut. Do not leave reeds in water longer than needed, as they turn dark; dampen them often while weaving so they pack down closer. He also mentions bleaching with chloride of lime in water set in sunlight, but warns too much gives a whitish look; it is not part of this blueprint.

প্রয়োজনীয় সরঞ্জাম:

চামড়া কাটার ছুরিচামড়া কাটার ছুরি
প্রোপেন মশালপ্রোপেন মশাল
8

Troubleshooting

Reed basket troubleshooting.

Flow

Loading...
9

History and honest limits

From "Reed Furniture: A Reed Basket" by Chas. M. Miller, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 257-260). Reed sizes are his trade numbers (No. 3, No. 4). Bleaching is described in his text but left out here. The tools and metric figures are ours.

উপকরণ

2
  • প্লেসহোল্ডার
  • 1 টুকরা
    প্লেসহোল্ডার

প্রয়োজনীয় সরঞ্জাম

8

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...