সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)
Woody

তৈরি করেছেন

Woody

13. নভেম্বর 2026NO
১০
০
০
০
০

Straight-Sided Guitar: Maple Box, Pine Top, Hatpin Frets and a 24-Inch Scale (Boy Mechanic, 1913)

A six-string guitar "having straight lines, giving it an old-fashioned appearance", from The Boy Mechanic (1913): a tapered box of hard maple with a seasoned soft-pine top, a drawknifed neck, frets cut from hatpins and a 24 in scale. Sizes are read on the 1913 scan. "If care is taken in selecting the material, and having it thoroughly seasoned, the finished instrument will have a fine tone."
উন্নত
About 1 week, with glue drying

নির্দেশাবলি

1

Cutting list and frets

Jupyter নোটবুক লোড হচ্ছে…
2

Read The Boy Mechanic

"The sides, ends and bottom are made of hard wood, preferably hard maple, and the top should be made of a thoroughly seasoned piece of soft pine." (J. H. Stoddard, Carbondale, Pa.)
3

Cut the pieces

Cut from thoroughly seasoned wood: top 3/16 by 14 by 17 in (soft pine); bottom 3/16 by 14 by 17 in, two sides 3/16 by 3-5/8 by 16-3/4 in, and ends 3/16 by 3-5/8 by 13-1/8 in and 9-5/8 in (hard maple); neck 1 by 2-5/16 by 18-1/2 in; fingerboard 3/16 by 2-5/8 by 16 in.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
পাইন কাঠের তক্তাপাইন কাঠের তক্তা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
ফিতা-মাপফিতা-মাপ
স্থির গুনিয়াস্থির গুনিয়া
4

Shape the neck and fingerboard

Taper the neck from G to F and from J to F, with the back rounded, using a drawknife: 2-3/8 in at the heel, 1-7/8 in at the nut F, and a head 2-3/4 in wide and 6-1/2 in long. Taper the fingerboard to match. Glue a piece of hard wood 1/4 in square and 1-7/8 in long across the neck at F as the nut. Glue the fingerboard to the neck and clamp it until the glue sets.

এই ধাপের উপকরণ:

শক্ত কাঠের ফালিশক্ত কাঠের ফালি1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

দুই হাতলের টানা ছুরিদুই হাতলের টানা ছুরি
হাত-করাতহাত-করাত
বার ক্ল্যাম্পবার ক্ল্যাম্প
5

Fret the fingerboard

Mark the frets from the nut using the computed positions in step 1 (fret 1 at 1.347 in, fret 12 at 12 in). His drawing gives only five spaces, 1-2/5, 1-3/16, 1-1/8, 1-1/16 and 1 in; added up they put the 5th fret about 0.3 in short of the true place, so they are shown for history only. Cut pieces from hatpins and fasten them across the fingerboard with small wire staples. Mark accurately: the frets decide the pitch.

এই ধাপের উপকরণ:

টুপির পিনটুপির পিন1 টুকরা
তারের স্টেপলতারের স্টেপল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
হাতুড়িহাতুড়ি
ফিতা-মাপফিতা-মাপ
স্থির গুনিয়াস্থির গুনিয়া
6

Build the box

Glue the sides and ends together, so the body is 10 in wide at the neck end, 13-1/2 in at the tail and 16-1/2 in long. Glue the front on, put heavy weights on top and give the glue time to dry. Fasten pieces of soft wood in the corners as braces, glue a small block C inside the neck end to take the bolt, and glue strips of soft wood K across the front and back to strengthen them. Cut the sound hole in the top as drawn.

এই ধাপের উপকরণ:

নরম কাঠের ব্যাটেননরম কাঠের ব্যাটেন1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
বার ক্ল্যাম্পবার ক্ল্যাম্প
হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
7

Fit the neck

Make the brace D 1 in thick, to any shape you like. Glue the neck to the box and secure it with a carriage bolt at A through the end and block C. Glue the back on and smooth the outside with sandpaper.

এই ধাপের উপকরণ:

শক্ত কাঠের ফালিশক্ত কাঠের ফালি1 টুকরা
গোল মাথার বোল্টগোল মাথার বোল্ট1 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
শিরিষ কাগজশিরিষ কাগজ1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
বার ক্ল্যাম্পবার ক্ল্যাম্প
8

Make and place the bridge

Make the bridge 6 in long, 1 in wide and 3/8 in high, with an old hatpin or wire of the same size secured on top with pin staples as the saddle E. Drill six 3/16 in holes in it for the pins. Glue it on the top so the distance from the nut F to the saddle E is just 24 in.

এই ধাপের উপকরণ:

শক্ত কাঠের ফালিশক্ত কাঠের ফালি1 টুকরা
টুপির পিনটুপির পিন1 টুকরা
তারের স্টেপলতারের স্টেপল1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
হাত-করাতহাত-করাত
ফিতা-মাপফিতা-মাপ
9

String it

Fit the turning pegs B in the head and string the guitar, holding the strings in the bridge with the pins. He bought the pegs and strings from a music store.

এই ধাপের উপকরণ:

সুর বাঁধার কাঠিসুর বাঁধার কাঠি1 টুকরা
গিটারের তারগিটারের তার1 টুকরা
ব্রিজ পিনব্রিজ পিন1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
10

Troubleshooting

Guitar troubleshooting.

Flow

Loading...
11

History and honest limits

From **The Boy Mechanic**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913, p. 320, "A Guitar That Is Easy to Make", sent in by J. H. Stoddard of Carbondale, Pa.; sizes read on the 1913 scan (archive.org boymechanicthing01unse). He dimensions only the first five fret spaces, and they disagree with equal temperament; the fret positions used are computed by us. The sound hole, saddle and string tensions are not dimensioned. The tools and metric figures are ours.

উপকরণ

12

প্রয়োজনীয় সরঞ্জাম

8

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...