সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য

Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)
George Edwinson's tong-making lesson from Amateur Work (1886): jaws forged from inch-square iron, reins of 5/8 in. rod scarfed and welded on, the halves riveted with a hot iron pin. The same flat-bit tongs are then reshaped into pincer, hammer and crook-bit tongs, light smith's pliers, and thinned and curved into crucible tongs.
উন্নত
A day at the forge
নির্দেশাবলি
1
1
His sizes
His sizes
Jupyter নোটবুক লোড হচ্ছে…
2
2
Read Edwinson
Read Edwinson
"Indeed, the man who can turn out a good pair of tongs may be trusted with almost any job in the smithy."
3
3
Forge the reins
Forge the reins
Cut two pieces of 5/8 in. (16 mm) iron rod, each 2 ft (0.6 m) long, with a cold chisel. Bring one end of each to a white welding heat and draw 3-4 in. down to a taper from 5/8 to 1/2 in., rounded for the hand. Upset the other ends at a white heat and scarf them (his figs. 27-28).
এই ধাপের উপকরণ:
পেটানো লোহার দণ্ড1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
ঠান্ডা ছেনি
কামারের ভাটি
নেহাই
হাতুড়ি
কামারের সাঁড়াশি4
4
Forge the jaws
Forge the jaws
Cut two 6 in. pieces of 1 in. square iron (or one 12 in. bar, worked from each end before cutting, fig. 29). Forge each jaw end 4 in. long, 1 1/4 in. wide and 3/8 in. thick. Flatten the other end to 1/4 in. thick, round it for the joint (fig. 30) and draw it to a slightly rounded taper (fig. 31).
এই ধাপের উপকরণ:
নরম ইস্পাতের চৌকো দণ্ড1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
কামারের ভাটি
নেহাই
হাতুড়ি
কামারের সাঁড়াশি5
5
Punch the joint
Punch the joint
Mark the hole with a centre punch, heat, and punch a 3/8 in. hole over the anvil's heel hole with an iron punch tapering 1/4 to 1/2 in. (fig. 35), or a steel punch of 5/8 in. tool steel.
এই ধাপের উপকরণ:
যন্ত্র-ইস্পাতের দণ্ড1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
কেন্দ্র-ছিদ্রক
কামারের ভাটি
নেহাই
হাতুড়ি6
6
Weld jaw to rein
Weld jaw to rein
Scarf the taper end of each jaw to fit a rein. Heat both to a welding heat in a clear fire, throw on clean fine fresh-water sand and heat until pasty. Tap the scarfs together lightly, return to the fire a moment, and finish the weld. At a red heat forge the square part to blend into the round rein (fig. 32).
এই ধাপের উপকরণ:
বালি1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
কামারের ভাটি
নেহাই
হাতুড়ি
কামারের সাঁড়াশি7
7
Rivet the joint
Rivet the joint
Smiths' way: nick a 3/8 in. round iron rod to rivet length, put the halves together, insert the hot end, twist it off, let 1/4 in. stand below, and rivet both sides. (Or make a 3/4 x 3/8 in. button-headed rivet in a 3/8 in. hole in a flat iron.) If the joint locks, reheat jaws and pin to bright red and work them free.
এই ধাপের উপকরণ:
পেটানো লোহার দণ্ড1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
কামারের ভাটি
নেহাই
হাতুড়ি
পেরেকের মাথা গড়ার পাত8
8
Set the jaws
Set the jaws
Heat the jaws and set them to the width of the stock to be held. Spring them wider with a piece of cold iron between and a few light blows.
প্রয়োজনীয় সরঞ্জাম:
কামারের ভাটি
নেহাই
হাতুড়ি9
9
Crucible tongs and other forms
Crucible tongs and other forms
From flat-bit tongs at the fig. 32 stage: lengthen and curve the bits for pincer tongs (angular notches hold round or square bars), more for hammer tongs, bend them sideways for crook-bit tongs. Small flat-bit tongs with lengthened, shaped bits are smith's pliers; thin those out further and curve them like pincers to make crucible tongs for hot crucibles and pots of molten metal. Heavy tongs 2-5 ft long need stouter iron.
প্রয়োজনীয় সরঞ্জাম:
কামারের ভাটি
নেহাই
হাতুড়ি
কামারের সাঁড়াশি10
10
Troubleshooting
Troubleshooting
Tongs troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" III, **Amateur Work, Illustrated**, vol. V (1886), pp. 266-269 (checked on the archive.org scan amateurworkillus05lond). He gives full sizes only for the flat-bit tongs; crucible tong sizes and curvature are left to the work. Metric figures and tools are ours.
উপকরণ
4- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
এই ব্লুপ্রিন্ট যা তৈরি করে
সম্পর্কিত ব্লুপ্রিন্ট
এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি
CC0 পাবলিক ডোমেন
এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।
মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।




