সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)
Volt

তৈরি করেছেন

Volt

14. নভেম্বর 2026SE
৯
০
০
০
০

Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)

The Victorian battery terminal, from George Edwinson's Electro-plating at Home (Amateur Work, 1881): a brass body turned from 1 1/2 in. of 5/8 in. rod, slotted for the plate and bored for the wire, with thumb screws turned from 3/8 in. rod; or a clamp bent hot from a brass strip with a soldered-on wire piece.
মধ্যবর্তী
Two hours at the lathe

নির্দেশাবলি

1

His sizes

Jupyter নোটবুক লোড হচ্ছে…
2

Read Edwinson

"Those who may have lathes ... may easily turn up a binding-screw ... out of a 1 1/2 in. length of 5/8 in. brass rod."
3

Turn the body

Cut 1 1/2 in. (38 mm) of 5/8 in. (16 mm) brass rod and turn the body to shape first (his fig. 3: a round head on a tapering neck over a forked foot).

এই ধাপের উপকরণ:

পিতলের দণ্ডপিতলের দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হ্যাকসহ্যাকস
ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
কাটার ছেনি (খরাদ)কাটার ছেনি (খরাদ)
4

Slot and bore

Cut the slot that grips the plate. Bore a hole for the wire through the head, then bore the holes for the screws.

প্রয়োজনীয় সরঞ্জাম:

বেঞ্চ ভাইসবেঞ্চ ভাইস
হ্যাকসহ্যাকস
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
হাত-ড্রিলহাত-ড্রিল
5

Turn the thumb screws

Turn the screws from 3/8 in. (9.5 mm) brass rod with plain thumb-screw heads (he says milled heads are a mistake). Cut a fine thread on them and tap the holes to match.

এই ধাপের উপকরণ:

পিতলের দণ্ডপিতলের দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
কাটার ছেনি (খরাদ)কাটার ছেনি (খরাদ)
প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
6

Bent clamp (variant)

From good malleable brass take a strip 3 in. long, 1/2 in. wide and 1/4 in. thick (76 x 13 x 6 mm). Heat it to a dull red and bend it over a former of hot iron. Cut the piece for the wire and centre screw separately, hard-solder it on and trim it. Fit thumb screws as above. (A clamp may also be cast from a wooden pattern.)

এই ধাপের উপকরণ:

পিতলের ফালিপিতলের ফালি1 টুকরা
রুপার সোল্ডাররুপার সোল্ডার1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

কামারের ভাটিকামারের ভাটি
কামারের সাঁড়াশিকামারের সাঁড়াশি
হাতুড়িহাতুড়ি
ব্রেজিং মশালব্রেজিং মশাল
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
হাত-ড্রিলহাত-ড্রিল
প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
7

Clean and keep it working

Clean the slot with folded emery cloth and the wire hole with the tang of a file. Now and then oil the screw, work it in and out, and wipe the oil off. Do not screw up too tight.

প্রয়োজনীয় সরঞ্জাম:

রেতি (হাতের রেতি)রেতি (হাতের রেতি)
8

Troubleshooting

Binding-screw troubleshooting.

Flow

Loading...
9

History and honest limits

From George Edwinson, "Electro-plating at Home", **Amateur Work, Illustrated**, vol. I (1881), p. 81 figs. 3 and 7 and p. 99 (checked on the archive.org scan amateurworkillus11881lond). He gives no thread size. Modern panel binding posts add an insulating bush and a banana-plug socket; this is the 1881 brass terminal. The metric figures and the tools are ours.

উপকরণ

3

প্রয়োজনীয় সরঞ্জাম

11

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...