সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Sprung-Blade Inclined-Dasher Churn: The Blades Close to Pass the Narrow Top and Spread to Fill the Wide Bottom
Woody

তৈরি করেছেন

Woody

9. নভেম্বর 2026NO
৯
০
০
০
০

Sprung-Blade Inclined-Dasher Churn: The Blades Close to Pass the Narrow Top and Spread to Fill the Wide Bottom

John U. Fiester of Winchester, Ohio, received US 22,945 in February 1859 for a churn with a slanting dasher in a tub wider at the bottom than the top, so it is hard to tip over. The dasher's two blades are held to the spindle by a yoke spring and guided by pins in the slots of a cross tie: they close to pass the narrow top and spread to fill the wide bottom. Holes let the cream through the blades, and square pockets cut part way in carry air down into it. This rung builds it in pine and hardwood with a crank.
মধ্যবর্তী
About 8 hours, plus printing

নির্দেশাবলি

1

Tub, fill and the blades' reach

Jupyter নোটবুক লোড হচ্ছে…
2

Holed beaters, before it

The Robies' beaters pass the cream through holes. Fiester's blades also have pockets that carry air down.
3

Read US 22,945

"... the yoke spring E and slots (a) allow the dasher blades to be forced easily into the smaller opening in the top of the tub, and when in to expand and fill the larger space at the bottom."
4

Print the journal box e

The block with the seat for the spindle's point. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
5

Print the yoke collar

The collar on the spindle that holds the yoke spring. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
6

Tub A and lid B

From 18 mm pine cut a floor 460 x 336 mm, two ends 400 mm wide at the foot, 320 mm at the top and 400 mm tall, and two sloping sides 336 mm wide that join them. Glue and screw the ends and sides on the floor so the tub is 400 mm wide inside at the floor and 320 mm at the top, 300 mm front to back. Cut a lid 374 x 336 mm with a turned dowel knob. Drill a 42 mm hole through the right side where the spindle meets it, about 345 mm above the inside floor.

এই ধাপের উপকরণ:

পাইন কাঠের তক্তাপাইন কাঠের তক্তা3 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু40 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
জিগস করাতজিগস করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
হোল-স সেটহোল-স সেট
ক্ল্যাম্পক্ল্যাম্প
চাঁদা / কোণমাপকচাঁদা / কোণমাপক
শিরিষ কাগজশিরিষ কাগজ
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
ফিতা-মাপফিতা-মাপ
7

Spindle C and journal e

Cut a 40 mm hardwood dowel 641 mm long and whittle or plane one end to a point over 30 mm. Screw the journal box in the left corner of the floor, against the sloping side. Cut a half-lap notch 30 mm wide and 12 mm deep across the spindle 85 mm from its point for the cross tie.

এই ধাপের উপকরণ:

PETG ফিলামেন্টPETG ফিলামেন্ট1 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু4 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ফিলামেন্টের 3D প্রিন্টার (FDM)ফিলামেন্টের 3D প্রিন্টার (FDM)
হাত-করাতহাত-করাত
বাটালিবাটালি
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
8

Blades D, tie F and yoke E

Draw an oval 340 x 220 mm on 16 mm hardwood and cut it in two along its length, then take 4 mm off each straight edge so the halves clear the spindle. Drill four 20 mm holes f in each blade and chisel four 20 mm square pockets d, 8 mm deep with bevelled sides, facing the same way. Glue a 9 mm dowel pin b into each blade 31 mm from its straight edge, 30 mm from its lower end. Cut a hardwood cross tie F 190 x 30 x 16 mm with a 10 mm slot 30 mm long near each end, glue it into the spindle's notch, and drop the pins into its slots. Slide the collar onto the spindle above the blades and screw two spring steel strips 15 x 1.5 mm, 42 mm long, from the collar to each blade's top end.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
স্প্রিং ইস্পাতের ফালিস্প্রিং ইস্পাতের ফালি1 টুকরা
যন্ত্র-স্ক্রুযন্ত্র-স্ক্রু8 টুকরা
নাইলন-ভরা লক নাটনাইলন-ভরা লক নাট8 টুকরা

প্রয়োজনীয় সরঞ্জাম:

জিগস করাতজিগস করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
কোদাল-বিট সেটকোদাল-বিট সেট
বাটালিবাটালি
হ্যাকসহ্যাকস
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
শিরিষ কাগজশিরিষ কাগজ
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
9

Fit the dasher and crank

Pass the spindle's top out through the hole in the right side, squeeze the blades together through the tub's top and let them spread, and seat the point in the journal box. Fix a hardwood crank arm 130 mm long on the spindle outside the tub with a screw across, and glue in a 24 mm dowel handle 100 mm long.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
কোদাল-বিট সেটকোদাল-বিট সেট
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
10

The build in 3D

FreeCAD model of this build, the near half of the tub cut away: the sloping tub, the journal box, the slanting spindle with its two holed blades, the cross tie with its slots and pins, the yoke collar and springs, and the crank outside.
নকশা ফাইলBLENDCC0 - Free
11

Churn

Pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and put the lid on. Turn the crank steadily and time it: the blades dip in and out of the cream, the pockets carrying air down. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

এই ধাপের উপকরণ:

ঘন ক্রিমঘন ক্রিম12 l
মোটা সমুদ্র লবণমোটা সমুদ্র লবণ1 টুকরা
জলজল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ভিতরে রেখে দেওয়া প্রোব থার্মোমিটারভিতরে রেখে দেওয়া প্রোব থার্মোমিটার
স্টপওয়াচস্টপওয়াচ
ডিজিটাল রান্নাঘরের দাঁড়িপাল্লাডিজিটাল রান্নাঘরের দাঁড়িপাল্লা
স্টেনলেস স্টিলের বড় মেশানোর বাটিস্টেনলেস স্টিলের বড় মেশানোর বাটি
12

Troubleshooting

Sprung-blade churn troubleshooting.

Flow

Loading...
13

History and honest limits

**John U. Fiester** of Winchester, Guernsey County, Ohio, US 22,945, "Churn": the drawing reads 15 February 1859, the text 25 February 1859. A tub wider at the top can be overset; his is wider at the bottom, and the sprung, guided blades still fill it. He claimed the adjustable dasher with its yoke spring, slotted cross tie and pins, holes and air pockets. He gave no sizes or materials: ours are a pine tub, hardwood dasher and steel springs.

উপকরণ

12

প্রয়োজনীয় সরঞ্জাম

18

ডিজাইন ফাইল

3

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...