সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
Forge

তৈরি করেছেন

Forge

13. নভেম্বর 2026NO
৮
০
০
০
০

Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)

Charles Gottschalk of St. Paul, Minnesota, received US 1,584,028, dated 11 May 1926, for a table saw with two saws. A crosscut saw and a rip saw stand at opposite corners of one table, so either or both can be used without changing blades. An electric motor inside the frame drives both through two chains. The top is hinged twice and lifted by a hand screw at either end, which sets each saw's depth of cut on its own. A lever with wheels lets two people truck the whole machine about. The patent gives no sizes; every size here is ours.
উন্নত
About 1 week

নির্দেশাবলি

1

Setting each saw's depth

Jupyter নোটবুক লোড হচ্ছে…
2

Read US 1,584,028

"Inasmuch as the saws are positioned fairly close to the hinges 19 and 23 the movement of the table for one of the saws does not appreciably affect the positioning of the same in regard to the other saw so that the depth of cut of either of the two saws may be adjusted independently or simultaneously if desired."
3

Frame on skids

From 45 x 95 mm pine: two skids 10, 11 1200 mm long; four uprights 12 775 mm long; two top rails 13 1300 mm long, their ends 50 mm past the uprights (17 at the rear, 18 at the front); cross rails 14, 15 between the uprights; a motor bed 52 across the skids. Glue and bolt the joints with carriage bolts, square and level, so the rails' tops stand 820 mm above the floor and 600 mm apart.

এই ধাপের উপকরণ:

পাইন কাঠপাইন কাঠ10 টুকরা
গোল মাথার বোল্টগোল মাথার বোল্ট24 টুকরা
সমতল ওয়াশারসমতল ওয়াশার24 টুকরা
ষড়ভুজ বাদামষড়ভুজ বাদাম24 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

জিগস করাতজিগস করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
কোদাল-বিট সেটকোদাল-বিট সেট
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
বার ক্ল্যাম্পবার ক্ল্যাম্প
যৌগিক স্কোয়্যারযৌগিক স্কোয়্যার
ফিতা-মাপফিতা-মাপ
4

Turn the two arbors

From 30 mm steel bar turn two arbors 26, 27, each 400 mm long. On one end of each turn a collar 40 mm across and 6 mm thick 30 mm from the end, and screw-cut the last 25 mm M20 on the lathe; turn a loose flange 60 mm across with a 20 mm bore for each. Drill and tap the sprockets' hubs for set screws if they have none.

এই ধাপের উপকরণ:

নরম ইস্পাতের গোল দণ্ডনরম ইস্পাতের গোল দণ্ড2 টুকরা
ষড়ভুজ বাদামষড়ভুজ বাদাম4 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
তিন-চোয়ালের খরাদ চাকতিন-চোয়ালের খরাদ চাক
খরাদের কাটার যন্ত্রখরাদের কাটার যন্ত্র
ডিজিটাল ক্যালিপার ৬ ইঞ্চিডিজিটাল ক্যালিপার ৬ ইঞ্চি
হ্যাকসহ্যাকস
স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেটড্রিল-বিট সেট
প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
ট্যাপ ঘোরানোর হাতলট্যাপ ঘোরানোর হাতল
সুরক্ষা চশমাসুরক্ষা চশমা
5

Mount the arbors and the saws

Bolt two 30 mm flange bearings 28 to the outsides of the rails for each arbor, its centre 30 mm below the rails' tops: the crosscut saw's arbor 27 250 mm from the front ends, the rip saw's arbor 26 250 mm from the rear ends. Push the arbors through so the crosscut saw's threaded end stands out past the left rail and the rip saw's past the right one, seen from the front. Fix a 17-tooth #40 sprocket on each arbor between the rails. Put each 250 mm blade on its collar, the teeth at the top pointing to the front, then the loose flange, a nut and a second nut locked against it.

এই ধাপের উপকরণ:

ফ্ল্যাঞ্জ বিয়ারিংফ্ল্যাঞ্জ বিয়ারিং4 টুকরা
চেনের দাঁতাল চাকাচেনের দাঁতাল চাকা2 টুকরা
Circular Saw Blade SetCircular Saw Blade Set1 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ16 টুকরা
বাটির মতো ডগাওয়ালা সেট স্ক্রুবাটির মতো ডগাওয়ালা সেট স্ক্রু4 টুকরা

প্রয়োজনীয় সরঞ্জাম:

সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
অ্যালেন চাবির সেটঅ্যালেন চাবির সেট
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
6

Motor and chains

Bolt the motor 51 to its bed between the skids under the arbors, its shaft parallel to them, and fit two 17-tooth sprockets 52 on its shaft, each in line with one arbor's sprocket. Fit a #40 chain 53, 54 from each to its arbor, tensioned by sliding the motor in slotted bolt holes. Have the motor wired to a switch within reach at the front. Oil the chains.

এই ধাপের উপকরণ:

বৈদ্যুতিক মোটরবৈদ্যুতিক মোটর1 টুকরা
চেনের দাঁতাল চাকাচেনের দাঁতাল চাকা2 টুকরা
রোলার শিকলরোলার শিকল2 টুকরা
চালু/বন্ধ সুইচচালু/বন্ধ সুইচ1 টুকরা
মেশিন তেলমেশিন তেল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
অ্যালেন চাবির সেটঅ্যালেন চাবির সেট
7

The hinged members and the top

Cut two hardwood members 20, 21 20 x 70 mm, 1340 mm long, to lie flat on the rails; hinge their front ends to the rails' front ends 19 and let them reach 40 mm past the rear 22. Cut the 18 mm plywood top 24 1400 x 800, with a slot over each blade, and hinge its rear edge to the members' rear ends 23. Rout a square groove 35 for the crosscut guide parallel to the crosscut saw and a second groove 200 on its other side, and a groove 42 across the top for the rip guide's bar.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা2 টুকরা
প্লাইউডের পাতপ্লাইউডের পাত1 টুকরা
দরজার কবজাদরজার কবজা4 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু40 টুকরা

প্রয়োজনীয় সরঞ্জাম:

জিগস করাতজিগস করাত
রাউটাররাউটার
রাউটার বিট সেটরাউটার বিট সেট
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
বার ক্ল্যাম্পবার ক্ল্যাম্প
যৌগিক স্কোয়্যারযৌগিক স্কোয়্যার
ফিতা-মাপফিতা-মাপ
8

The depth screws

Screw a 6 mm steel plate under each rail's projecting end, drilled and tapped M12. Run a 150 mm M12 threaded rod up through each, with a wing nut locked on its lower end as a handle. The rear pair 156 push up under the members' rear ends 22, lifting members and top on the front hinges 19: this sets the rip saw. The front pair 157 pass through holes 58 in the members and push the top alone up on its rear hinges 23: this sets the crosscut saw.

এই ধাপের উপকরণ:

নরম ইস্পাতের চ্যাপ্টা পাটানরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
প্যাঁচকাটা দণ্ডপ্যাঁচকাটা দণ্ড4 টুকরা
প্রজাপতি নাটপ্রজাপতি নাট4 টুকরা
ষড়ভুজ বাদামষড়ভুজ বাদাম4 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু16 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হ্যাকসহ্যাকস
স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেটড্রিল-বিট সেট
প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
ট্যাপ ঘোরানোর হাতলট্যাপ ঘোরানোর হাতল
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
9

The guides

Crosscut guide: a hardwood bar 39 sliding in groove 35, with an angle fence 37 pivoted on it at 36 and clamped at any angle by a wing nut 40 through an arc slot 38. Rip guide: a bar 43 sliding in groove 42, held by a hand screw 49 through a plate 50, carrying a fence 45 hinged on a bracket 44 and tilted by a wing nut 67 in an arc slot 47.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
গোল মাথার বোল্টগোল মাথার বোল্ট4 টুকরা
প্রজাপতি নাটপ্রজাপতি নাট3 টুকরা
নরম ইস্পাতের চ্যাপ্টা পাটানরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

জিগস করাতজিগস করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
যৌগিক স্কোয়্যারযৌগিক স্কোয়্যার
10

The truck

Pivot two hardwood arms 60, 61 to the rear ends of the skids at 66, with a wheel 62 on the end of each beyond the pivot. Their front ends 63 are handles sliding in keepers 64 on the front uprights. With the handles down, the wheels are off the floor; lift the handles and the wheels take the weight so the saw can be wheeled away.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা2 টুকরা
রবার চাকার সেটরবার চাকার সেট1 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ4 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু8 টুকরা

প্রয়োজনীয় সরঞ্জাম:

জিগস করাতজিগস করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
11

Try it

Wind both screw pairs down and check each blade stands square to the top and parallel to its groove. Set the rip saw's depth with the rear screws and the crosscut's with the front screws, each about 10 mm above the wood. Wearing glasses and ear defenders, rip a board along the rip guide, then cut the end off another against the crosscut guide.

প্রয়োজনীয় সরঞ্জাম:

যৌগিক স্কোয়্যারযৌগিক স্কোয়্যার
ফিতা-মাপফিতা-মাপ
সুরক্ষা চশমাসুরক্ষা চশমা
শ্রবণ-রক্ষক (কান-ঢাকনা, SNR 30 dB)শ্রবণ-রক্ষক (কান-ঢাকনা, SNR 30 dB)
12

Troubleshooting

Twin-saw table troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles Gottschalk** of St. Paul, Minnesota, US 1,584,028, dated 11 May 1926, filed 1 August 1921. He claimed a frame with two rails, longitudinal members hinged to the rails at one end, a single top hinged to them at the other, a crosscut saw at one end and a rip saw at the other through the top, and means to oscillate the members and top together, and the top alone, "so as to vary the relative depth of cut of either of said saws". He says a gasoline engine may drive it instead of the motor. His grooves are dovetailed; ours are square. He gives no sizes, speeds or sprocket sizes; all of those are ours.

উপকরণ

23

প্রয়োজনীয় সরঞ্জাম

21

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...