সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)
Tex

তৈরি করেছেন

Tex

14. নভেম্বর 2026FO
৮
০
০
০
০

Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)

How a harness maker cuts and finishes straps, from P. N. Hasluck's Harness Making (1904): marked along the hide with an 8 ft straightedge or a compass, cut with the round knife on a cutting-board (or with a plough gauge, 1/2 to 5-1/2 in), always along the hide, then the edges knocked, trimmed with the spokeshave, scraped, sanded and polished with gum and a smooth bone.
শিক্ষানবিশ
About 1 hour

নির্দেশাবলি

1

Widths

Jupyter নোটবুক লোড হচ্ছে…
2

Read Harness Making

"Straps are always cut along the hide and not across it, the hide being much stronger lengthways."
3

Lay out

Lay the side on the bench with the back toward you. Mark straight lines with a blunt-pointed awl or seat-awl against a straightedge at least 8 ft long, without cutting the grain. Do not cut lower into the hide than the strap's width; cut shaped pieces from patterns.

এই ধাপের উপকরণ:

হার্নেসের চামড়াহার্নেসের চামড়া1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

সোজা ধারসোজা ধার
জিন-কারিগরের গোল সুঁচ (সিট অল)জিন-কারিগরের গোল সুঁচ (সিট অল)
4

Cut

With the round knife: set the compass to the width, run one point along the edge and draw it toward you to leave a line, then cut from the right-hand end on a cutting-board, holding the leather steady with the left hand. With the plough: set the knife on the gauge (1/2 to 5-1/2 in) with the thumb-screw, hold the leather flat and press it forward with the guard tight to the edge. Cut reins first, then traces, back-bands and the rest; linings from the belly.

প্রয়োজনীয় সরঞ্জাম:

রেস কম্পাসরেস কম্পাস
চামড়া কাটার ছুরিচামড়া কাটার ছুরি
কাটার তক্তাকাটার তক্তা
5

Finish the edges

Knock the edges along to consolidate them, trim them round and level with the spokeshave, run a glass scraper over them and sandpaper. For brown work, wipe with a thin solution of gum and water and rub with brown paper and a smooth bone to a polish. For black, dye, rub dry with a rag, and polish with brown paper and bone.

এই ধাপের উপকরণ:

গঁদ (গাম অ্যারাবিক)গঁদ (গাম অ্যারাবিক)1 টুকরা
বাদামি মোড়ক কাগজবাদামি মোড়ক কাগজ1 টুকরা
শিরিষ কাগজশিরিষ কাগজ1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

দুই হাতলের রান্দাদুই হাতলের রান্দা
কাচের ভাঙা টুকরাকাচের ভাঙা টুকরা
হাড়ের ভাঁজ-যন্ত্রহাড়ের ভাঁজ-যন্ত্র
হাতুড়িহাতুড়ি
6

Troubleshooting

Strap troubleshooting.

Flow

Loading...
7

History and honest limits

From Paul N. Hasluck, **Harness Making** (1904) (checked on the archive.org scan harnessmaking00hasl, pp. 12, 42-44). Using broken glass (cullet) as the glass scraper, the tools and the metric figures are ours.

উপকরণ

4

প্রয়োজনীয় সরঞ্জাম

9

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...