সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Saddle Breastplate: Rounded Side Straps, Neck Strap and Girth Strap on Covered Rings (Hasluck, Saddlery, 1904)
Tex

তৈরি করেছেন

Tex

13. নভেম্বর 2026FO
৫
০
০
০
০

Saddle Breastplate: Rounded Side Straps, Neck Strap and Girth Strap on Covered Rings (Hasluck, Saddlery, 1904)

A breastplate stops a riding saddle sliding backwards, as a crupper stops it sliding forwards. This is the hunting saddle breastplate from Paul N. Hasluck's Saddlery (1904): two rounded side straps from the shoulders to a ring at the chest, a cross strap over the neck, two small buckle straps to the saddle staples, and a strap between the forelegs to the girth. Every size is his.
উন্নত
About 1 day

নির্দেশাবলি

1

His sizes in centimetres

Jupyter নোটবুক লোড হচ্ছে…
2

Read Saddlery, ch. V

"Breastplates (Fig. 10) are made for hunting saddles to prevent them falling backwards, just as the crupper keeps them from advancing too far."
3

Get the rings and buckles

You need one 1-1/2 in covered ring, two 1 in covered rings, two 5/8 in covered buckles and one 1 in covered buckle.

এই ধাপের উপকরণ:

চামড়া মোড়া আংটাচামড়া মোড়া আংটা3 টুকরা
চামড়া মোড়া বকলসচামড়া মোড়া বকলস3 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ফিতা-মাপফিতা-মাপ
4

Make the two side straps

Cut two side straps 7/8 in wide and 2 ft long when turned over the rings at each end. Round the top on the groove board, stuffing it with strands of soft cord. Stitch them along both sides very finely with silk cotton or linen thread, putting a 1 in ring at one end of each and both other ends into the 1-1/2 in ring. Polish the edges well after stitching.

এই ধাপের উপকরণ:

হার্নেসের চামড়াহার্নেসের চামড়া1 টুকরা
দড়িদড়ি1 টুকরা
মসিনার সুতামসিনার সুতা1 টুকরা
মৌমাছির মোমমৌমাছির মোম1 টুকরা
চামড়া মোড়া আংটাচামড়া মোড়া আংটা3 টুকরা

প্রয়োজনীয় সরঞ্জাম:

চামড়া কাটার ছুরিচামড়া কাটার ছুরি
খাঁজ কাটা বোর্ডখাঁজ কাটা বোর্ড
আউল (ছিদ্রকারী)আউল (ছিদ্রকারী)
দুটি জিন-সেলাইয়ের সুচদুটি জিন-সেলাইয়ের সুচ
চামড়া সেলাইয়ের কাঠের চিমটাচামড়া সেলাইয়ের কাঠের চিমটা
চামড়ার কিনারার ঘষনিচামড়ার কিনারার ঘষনি
ফিতা-মাপফিতা-মাপ
5

Make the cross strap

Cut a 1-3/8 in strap to be 10 in long when bent over the rings at each end; shave the ends and prick the sides finely like the shoulder piece. Cut another piece 9-1/4 in long when bent for the rings, 7/8 in wide at both ends and widening gradually to 1-3/4 in in the centre. Put the chapes in the 1 in rings and stitch both pieces together.

এই ধাপের উপকরণ:

হার্নেসের চামড়াহার্নেসের চামড়া1 টুকরা
মসিনার সুতামসিনার সুতা1 টুকরা
মৌমাছির মোমমৌমাছির মোম1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

চামড়া কাটার ছুরিচামড়া কাটার ছুরি
চামড়ার সেলাই ছেনিচামড়ার সেলাই ছেনি
আউল (ছিদ্রকারী)আউল (ছিদ্রকারী)
দুটি জিন-সেলাইয়ের সুচদুটি জিন-সেলাইয়ের সুচ
চামড়া সেলাইয়ের কাঠের চিমটাচামড়া সেলাইয়ের কাঠের চিমটা
ফিতা-মাপফিতা-মাপ
6

Make the two buckle straps

Make two 5/8 in straps 2 ft long, one end prepared for the buckle, the other narrowed; edge, rub and crease them with a hot checker. Put one in each 1 in ring to within 3 in of the buckle. Double the 3 in length with the buckle on top and make two loops between the two leathers. Stitch from the ring along both sides to the buckle, fastening the loops at the same time. Finish the edges of the stitched part and make seven or eight holes in the points.

এই ধাপের উপকরণ:

হার্নেসের চামড়াহার্নেসের চামড়া1 টুকরা
চামড়া মোড়া বকলসচামড়া মোড়া বকলস2 টুকরা
মসিনার সুতামসিনার সুতা1 টুকরা
মৌমাছির মোমমৌমাছির মোম1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

চামড়া কাটার ছুরিচামড়া কাটার ছুরি
প্রান্ত চাঁছার যন্ত্রপ্রান্ত চাঁছার যন্ত্র
চামড়ার কিনারার ঘষনিচামড়ার কিনারার ঘষনি
ভাঁজ করার সরঞ্জামভাঁজ করার সরঞ্জাম
প্রোপেন মশালপ্রোপেন মশাল
লুপ স্টিকলুপ স্টিক
আউল (ছিদ্রকারী)আউল (ছিদ্রকারী)
দুটি জিন-সেলাইয়ের সুচদুটি জিন-সেলাইয়ের সুচ
চামড়ার ছিদ্র করার পাঞ্চচামড়ার ছিদ্র করার পাঞ্চ
7

Make the girth strap

Cut a strap 1-1/4 in wide and 3 ft long. Narrow it to 1 in at 1 ft from the bend at the ring and turn it down for the 1 in buckle at the narrow end; edge, rub and crease it, then put the buckle in the reverse way. Cut eight or nine holes, beginning about 8 in from the buckle, and buckle the strap back on itself to make a loop for the girth (bellyband) to pass through.

এই ধাপের উপকরণ:

হার্নেসের চামড়াহার্নেসের চামড়া1 টুকরা
চামড়া মোড়া বকলসচামড়া মোড়া বকলস1 টুকরা
মসিনার সুতামসিনার সুতা1 টুকরা
মৌমাছির মোমমৌমাছির মোম1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

চামড়া কাটার ছুরিচামড়া কাটার ছুরি
প্রান্ত চাঁছার যন্ত্রপ্রান্ত চাঁছার যন্ত্র
চামড়ার কিনারার ঘষনিচামড়ার কিনারার ঘষনি
ভাঁজ করার সরঞ্জামভাঁজ করার সরঞ্জাম
প্রোপেন মশালপ্রোপেন মশাল
আউল (ছিদ্রকারী)আউল (ছিদ্রকারী)
দুটি জিন-সেলাইয়ের সুচদুটি জিন-সেলাইয়ের সুচ
চামড়ার ছিদ্র করার পাঞ্চচামড়ার ছিদ্র করার পাঞ্চ
8

Fit the safe

Put the other end of the girth strap in the 1-1/2 in ring. Cut a safe to go under it, running up under the ring round the top part and down about 3-1/2 in below the bend, narrowing towards the end almost to the width of the strap. Crease the safe and place it under the chape and ring; stitch it down on both sides with a fancy stitch in the centre. Line the safe with chamois or very thin buff, stitched in all round, stuff a little flock through the opening at the bottom, and close the opening with fancy stitching such as an arrow point. He adds that it can be made of single leather without lining, only the bends being stitched.

এই ধাপের উপকরণ:

হার্নেসের চামড়াহার্নেসের চামড়া1 টুকরা
শ্যামোয়া চামড়াশ্যামোয়া চামড়া1 টুকরা
পশমের ফ্লকপশমের ফ্লক1 টুকরা
মসিনার সুতামসিনার সুতা1 টুকরা
মৌমাছির মোমমৌমাছির মোম1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

চামড়া কাটার ছুরিচামড়া কাটার ছুরি
ভাঁজ করার সরঞ্জামভাঁজ করার সরঞ্জাম
প্রোপেন মশালপ্রোপেন মশাল
আউল (ছিদ্রকারী)আউল (ছিদ্রকারী)
দুটি জিন-সেলাইয়ের সুচদুটি জিন-সেলাইয়ের সুচ
চামড়া সেলাইয়ের কাঠের চিমটাচামড়া সেলাইয়ের কাঠের চিমটা
9

Put it on the horse

The long side straps run down from the shoulder to the chest, and the short cross strap passes over the neck at the top. The two small straps buckle to the staples in front of the saddle, and the girth strap runs from the big ring under the belly between the forelegs to the girth.
10

Troubleshooting

Breastplate troubleshooting.

Flow

Loading...
11

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter V, "Saddle Cruppers, Breastplates, and Other Accessories", breastplates, pp. 41-44, Fig. 10; every fraction was read on the scan. He says the cross strap is pricked "like the shoulder piece" without describing a shoulder piece; check the cross strap against Fig. 10. The crupper, martingale, girths, stirrup leathers and saddle cloths of the same chapter are not made here. The tools and metric figures are ours.

উপকরণ

8

প্রয়োজনীয় সরঞ্জাম

13

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...