সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition
Martin

তৈরি করেছেন

Martin

9. নভেম্বর 2026NO
১০
০
০
০
০

Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition

W. H. McClintock of Frankfort, Ohio, received US 24,223, dated 31 May 1859, for a churn that is a pump. A box is divided by a perforated partition into a cream chamber and a butter chamber. In the cream chamber a half-round pump has a vane swung back and forth by a lever: each stroke sucks cream up through a passage round the pump and flap valves into one side, and forces the other side's cream up through valves on top into a channel that runs into the butter chamber. The cream strains back through the partition and goes round again, chafed at every pass, until the butter is left in the butter chamber. Pumping water round the same way rinses the churn and washes the butter. This rung builds it in a pine box with a printed pump.
উন্নত
About 1 day, plus printing

নির্দেশাবলি

1

What one stroke moves

Jupyter নোটবুক লোড হচ্ছে…
2

Cream thrown over a partition, before it

Patterson's fan threw cream over a partition to return under it. McClintock pumps it over and strains it back.
3

Read US 24,223

"The cream first expelled flows into the chamber C, and by reason of the continued suction of the piston is caused to strain through the perforated partition D, and enter the cream or milk chamber again ready to be again similarly circulated, minus a greater portion of its fatty matter, said fatty matter remaining in the chamber C."
4

Print the pump E

The pump body: half-round chamber a, passage b round it with its inlet below, ports for valves c c'. Print it upside down on its flat top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
5

Print the vane f

The piston vane with its half-round hub. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
6

Box A and partition D

From 18 mm pine make a box 500 x 220 mm and 300 mm deep inside, with a lid and knob. Screw pairs of 10 mm strips down both side walls 300 mm from the left end as grooves, and slide in a 12 mm plywood partition D 212 mm high, drilled all over with 8 mm holes 20 mm apart, with a knob to lift it. Fit a PVC spigot low in the right end, in chamber C, as the opening j.

এই ধাপের উপকরণ:

পাইন কাঠের তক্তাপাইন কাঠের তক্তা3 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু40 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
প্লাইউডের পাতপ্লাইউডের পাত1 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
PVC কলPVC কল1 টুকরা
সিলিকন সিল্যান্টসিলিকন সিল্যান্ট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
জিগস করাতজিগস করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
হোল-স সেটহোল-স সেট
ক্ল্যাম্পক্ল্যাম্প
শিরিষ কাগজশিরিষ কাগজ
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
ফিতা-মাপফিতা-মাপ
7

Pump E and top plate

Cut a 12 mm plywood top plate 290 x 220 mm to fill chamber B from the left end to the partition. Cut a half-round groove across its underside for the vane's hub, 37 mm wide, centred 150 mm from the left end, and drill two 20 mm eduction holes d d' 50 mm each side of it. Glue rubber-sheet flaps e e' 32 mm square over them on top, hinged on one edge with a screw. Glue rubber flaps c c' over the two ports inside the pump's chamber, hinged at the top so they open inward. Screw the pump body under the plate, seal the joint with silicone, and rest the plate on cleats 200 mm above the floor so it closes chamber B.

এই ধাপের উপকরণ:

PETG ফিলামেন্টPETG ফিলামেন্ট1 টুকরা
প্লাইউডের পাতপ্লাইউডের পাত1 টুকরা
রবারের পাতরবারের পাত1 টুকরা
সিলিকন সিল্যান্টসিলিকন সিল্যান্ট1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু12 টুকরা
পাইন কাঠের তক্তাপাইন কাঠের তক্তা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ফিলামেন্টের 3D প্রিন্টার (FDM)ফিলামেন্টের 3D প্রিন্টার (FDM)
জিগস করাতজিগস করাত
হোল-স সেটহোল-স সেট
কাজের ছুরিকাজের ছুরি
তারবিহীন তুরপুনতারবিহীন তুরপুন
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
8

Vane f, lever g and channel F

Fix the vane on a 12 mm stainless rod with an M4 screw across, set it in the chamber with the hub in the plate's groove, and pass the rod out through the pump's end and the box's near wall. Fix a hardwood lever g 24 x 12 mm, 245 mm long, on the rod outside, standing up past the lid, with a 28 mm dowel handle on top. Fix a pine board above the top plate, sloping down from 258 mm high at the left end to 238 mm over the partition, to form channel F into C.

এই ধাপের উপকরণ:

স্টেনলেস স্টিলের দণ্ডস্টেনলেস স্টিলের দণ্ড1 টুকরা
যন্ত্র-স্ক্রুযন্ত্র-স্ক্রু1 টুকরা
নাইলন-ভরা লক নাটনাইলন-ভরা লক নাট1 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
পাইন কাঠের তক্তাপাইন কাঠের তক্তা1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু8 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হ্যাকসহ্যাকস
হাত-করাতহাত-করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
9

The build in 3D

FreeCAD model of this build, the near half cut away: box A with partition D in its grooves, the pump body with passage b and its inlet, the vane, the top plate with flaps e e', flaps c c' at the ports, channel F's board and the spigot. It was checked at five vane angles from -60 to +60 degrees.
নকশা ফাইলBLENDCC0 - Free
10

Churn

Pour about 8 litres of heavy cream at about 15 °C into chamber B through C (it strains through the partition), checked with the thermometer, and put the lid on. Swing the lever steadily back and forth about 60 degrees each way and time it: cream spurts into channel F, runs into C and strains back. When the butter has gathered in C, draw off the buttermilk at the spigot, pour cold water in and pump it round to rinse the churn and wash the butter, then lift the butter out, work in a pinch of salt and weigh it.

এই ধাপের উপকরণ:

ঘন ক্রিমঘন ক্রিম8 l
জলজল1 টুকরা
মোটা সমুদ্র লবণমোটা সমুদ্র লবণ1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ভিতরে রেখে দেওয়া প্রোব থার্মোমিটারভিতরে রেখে দেওয়া প্রোব থার্মোমিটার
স্টপওয়াচস্টপওয়াচ
ডিজিটাল রান্নাঘরের দাঁড়িপাল্লাডিজিটাল রান্নাঘরের দাঁড়িপাল্লা
স্টেনলেস স্টিলের বড় মেশানোর বাটিস্টেনলেস স্টিলের বড় মেশানোর বাটি
11

Troubleshooting

Pump churn troubleshooting.

Flow

Loading...
12

History and honest limits

**W. H. McClintock** of Frankfort, Ross County, Ohio, US 24,223, 31 May 1859, "Churn". He claimed the circularly vibrating suction and force pump with a churn having a perforated partition. He gave no sizes or materials: the box, the printed pump, the rubber flaps and every size are ours.

উপকরণ

16

প্রয়োজনীয় সরঞ্জাম

16

ডিজাইন ফাইল

3

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...