সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Pendulum Twin-Dasher Churn: A Swinging Weighted Lever Rocks a Beam That Works Two Half-Dashers Alternately
Martin

তৈরি করেছেন

Martin

9. নভেম্বর 2026NO
১১
০
০
০
০

Pendulum Twin-Dasher Churn: A Swinging Weighted Lever Rocks a Beam That Works Two Half-Dashers Alternately

James O. Merrill of Chichester, New Hampshire, received US 23,986, dated 10 May 1859, for an oscillating churn light enough to be worked by a child. A weighted pendulum behind the frame rocks a shaft; on its front end a beam rocks, and two links from the beam's ends work two dasher arms up and down in turn through slots in a guide bar. Each arm carries a half-round dasher pierced with holes, so the two halves fill the barrel. The two-piece cover is held down by a thumb screw. This rung builds it full size in timber over a 20-litre bucket.
মধ্যবর্তী
About 2 days

নির্দেশাবলি

1

How far the dashers move

Jupyter নোটবুক লোড হচ্ছে…
2

Two dashers worked in turn, before it

Mitchell's lever worked two dashers in turn; Merrill's weighted pendulum keeps them going with less effort.
3

Read US 23,986

"... the operator oscillates the lever L, which communicates the motion through the vibrating shaft M, the vibrating lever E, the auxiliary levers F, F', to the dasher arms G, G', thus producing an alternate reciprocating action of the dashers N, N'".
4

Base and frame

Cut a pine base A 720 x 520 mm. Stand two side pieces B B' of 44 x 70 mm timber 960 mm tall, 400 mm apart, 200 mm from the base's back edge, with diagonal side braces I I' and front braces H H' to the base. Screw top braces C C' (444 x 60 x 22 mm) across the front and back faces of the side pieces at the top, and bore both 21 mm in the middle, 30 mm below their top edge.

এই ধাপের উপকরণ:

পাইন কাঠের তক্তাপাইন কাঠের তক্তা2 টুকরা
নরম কাঠ ৭০x৭০ মিমিনরম কাঠ ৭০x৭০ মিমি4 টুকরা
কাঠের স্ক্রু #10 x 3"কাঠের স্ক্রু #10 x 3"30 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
কোদাল-বিট সেটকোদাল-বিট সেট
ক্ল্যাম্পক্ল্যাম্প
জলের সমতা মাপকজলের সমতা মাপক
ফিতা-মাপফিতা-মাপ
5

Shaft M, lever E and pendulum L

Screw a hardwood bearing block 80 x 80 x 18 mm, bored 20.5 mm, over each hole. Cut a 20 mm steel shaft 310 mm long and pass it through both. On its front end fix a hardwood lever E 400 x 60 x 20 mm at its middle with a bolt across, drilled 8.5 mm 150 mm each side of the middle for the pins c. On its back end fix the pendulum L, a hardwood bar 50 x 20 mm, 810 mm long, 60 mm below its top. Glue a 24 mm dowel handle h into L 180 mm below the shaft and bolt an 8 kg kettlebell to its foot as W.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা2 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু8 টুকরা
ইস্পাতের কাঁচা দণ্ডইস্পাতের কাঁচা দণ্ড1 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ3 টুকরা
নাইলন-ভরা লক নাটনাইলন-ভরা লক নাট3 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
কেটলবেলকেটলবেল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
কোদাল-বিট সেটকোদাল-বিট সেট
হ্যাকসহ্যাকস
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
6

Guide bar J, arms G and links F

Bolt a hardwood guide bar J 444 x 40 x 36 mm across the side pieces' fronts on spacer blocks so it stands 70 mm in front of them, 530 mm above the base, and cut two 27 mm square slots through it 40 mm apart. Cut two hardwood dasher arms G G' 25 mm square and 580 mm long, drop them through the slots, and drill each 8.5 mm 20 mm below its top. Cut two links F F' 30 x 14 mm with holes 282 mm apart and bolt each from a pin c on E to a pin g on an arm, with washers and lock nuts so they turn freely.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা2 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ6 টুকরা
সমতল ওয়াশারসমতল ওয়াশার8 টুকরা
নাইলন-ভরা লক নাটনাইলন-ভরা লক নাট4 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
বাটালিবাটালি
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
7

Barrel D, covers, dashers and thumb screw

Stand a food-grade 20-litre bucket on the base under the arms. Cut two half-discs N N' 240 mm across from 12 mm plywood, each with three 34 mm holes, and screw one under each arm's foot. Cut two half-round covers m m from 12 mm plywood to fit the bucket's top, notched for the arms. Bolt a cross brace K 444 x 40 x 30 mm across the side pieces' fronts 440 mm above the base, drill it for an M8 rod 72 mm behind the arms, and run the rod through a nut in K with a wing nut on top as the thumb screw i, down onto an oblong block l laid across both covers.

এই ধাপের উপকরণ:

২০ লিটারের বালতি২০ লিটারের বালতি1 টুকরা
প্লাইউডের পাতপ্লাইউডের পাত2 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু6 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ2 টুকরা
প্যাঁচকাটা দণ্ডপ্যাঁচকাটা দণ্ড1 টুকরা
ষড়ভুজ বাদামষড়ভুজ বাদাম1 টুকরা
প্রজাপতি নাটপ্রজাপতি নাট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

জিগস করাতজিগস করাত
হোল-স সেটহোল-স সেট
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
8

The build in 3D

FreeCAD model of this build, a quarter of the barrel and covers cut away: the base and frame with its braces, shaft M with lever E in front and the weighted pendulum behind, links F, the arms in guide bar J, the two half-dashers in the barrel, and the thumb screw on its block. It was checked at five pendulum angles from -12 to +12 degrees.
নকশা ফাইলBLENDCC0 - Free
9

Churn

Lift the front cover, pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, put the cover back and turn the thumb screw down on the block. Swing the pendulum by its handle about 12 degrees each way and time it: the half-dashers rise and fall in turn. When the butter comes, slacken the screw, unbolt the dashers, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

এই ধাপের উপকরণ:

ঘন ক্রিমঘন ক্রিম10 l
মোটা সমুদ্র লবণমোটা সমুদ্র লবণ1 টুকরা
জলজল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ভিতরে রেখে দেওয়া প্রোব থার্মোমিটারভিতরে রেখে দেওয়া প্রোব থার্মোমিটার
স্টপওয়াচস্টপওয়াচ
ডিজিটাল রান্নাঘরের দাঁড়িপাল্লাডিজিটাল রান্নাঘরের দাঁড়িপাল্লা
স্টেনলেস স্টিলের বড় মেশানোর বাটিস্টেনলেস স্টিলের বড় মেশানোর বাটি
10

Troubleshooting

Pendulum churn troubleshooting.

Flow

Loading...
11

History and honest limits

**James O. Merrill** of Chichester, Merrimack County, New Hampshire, assignor to Wm. A. Swain, US 23,986, 10 May 1859, "Churn". He meant it to take the labour out of churning, adapted to the strength of a child, and claimed the pendulum and weight with the shaft, beam, links and the two alternate dasher arms. He gave no sizes or weight: the frame, the 8 kg weight, the 12 degree swing and every size are ours.

উপকরণ

20

প্রয়োজনীয় সরঞ্জাম

17

ডিজাইন ফাইল

1

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...