সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)
Forge

তৈরি করেছেন

Forge

13. নভেম্বর 2026NO
১৩
০
০
০
০

Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)

Frank L. Pritchard of Parker, Arizona, received US 2,231,593, dated 11 February 1941, for a tubing cutter small enough for a mechanic's tool box. The tube sits in a V in a fixed jaw. A movable jaw slides on the adjusting screw and a guide pin, with a spring pushing the jaws apart. The cutting wheel is held by a pivoted support with threads on its inner edge. Swung down, the support lets go of the screw, so the jaw can be pushed straight onto any tube. Swung up, it meshes with the screw again and the screw feeds the wheel in. We make his parts from steel bar and plate. All sizes are ours.
মধ্যবর্তী
About 3 days

নির্দেশাবলি

1

The swing that lets go

Jupyter নোটবুক লোড হচ্ছে…
2

Read US 2,231,593

"The pivoted blade support 16 may swing downwardly until the threads thereof will be free of the threads of the screw 8. The movable jaw 6 may now be slid downwardly until the pivoted blade support is in its proper cutting position."
3

Print the template

Both jaws, the blade support, the wheel and a 15 mm tube at 1:1, with the screw, pin and pivot holes. print at 100 % (check the 50 mm bar).
নকশা ফাইলPDFCC0 - Free
4

Make the stationary jaw

Saw 64 mm of 16 mm square bar, or of 16 mm plate. File the 90 degree V 8 mm deep in its top face. Drill the 6 mm pin hole and a 10 mm hole for the screw, and counterbore the pin hole 10 mm across, 5 mm deep, for the spring. Drill the 3 mm cross-pin hole across the jaw so it just cuts into the side of the screw hole.

এই ধাপের উপকরণ:

নরম ইস্পাতের প্লেটনরম ইস্পাতের প্লেট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হ্যাকসহ্যাকস
উকো-সেটউকো-সেট
স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
মেশিন ভাইসমেশিন ভাইস
ড্রিল-বিট সেটড্রিল-বিট সেট
কেন্দ্র-ছিদ্রককেন্দ্র-ছিদ্রক
দাগ টানার শলাকাদাগ টানার শলাকা
বেঞ্চ ভাইসবেঞ্চ ভাইস
ডিজিটাল ক্যালিপার ৬ ইঞ্চিডিজিটাল ক্যালিপার ৬ ইঞ্চি
5

Make the movable jaw and the support

Saw the movable jaw 50 mm long from the same bar. Drill the 6.2 mm pin hole and its spring counterbore. Saw and file a slot 8.2 mm wide down its middle, from 22 mm to the end. Saw the blade support from 14 mm plate to the template. File its upper part down to 8 mm thick, centred, so it slides into the slot, and file away its lower inner corner. Saw a 7 mm slot up its lower part for the wheel. Drill the pivot and stop-pin holes through the jaw and support together, and file the stop-pin hole in the support into a short slot.

এই ধাপের উপকরণ:

নরম ইস্পাতের প্লেটনরম ইস্পাতের প্লেট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হ্যাকসহ্যাকস
উকো-সেটউকো-সেট
সূক্ষ্ম উকোর সেটসূক্ষ্ম উকোর সেট
স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
মেশিন ভাইসমেশিন ভাইস
ড্রিল-বিট সেটড্রিল-বিট সেট
বেঞ্চ ভাইসবেঞ্চ ভাইস
ডিজিটাল ক্যালিপার ৬ ইঞ্চিডিজিটাল ক্যালিপার ৬ ইঞ্চি
6

Tap the half nut

Pin the support in the jaw, swung up, and clamp it there. Drill 6.8 mm down the screw axis through both, so the drill cuts a shallow groove in the support's inner edge, then tap it M8 through both. Take the support out and open the jaw's own hole to 8.5 mm, so the screw passes freely and only the support's threads hold it.

প্রয়োজনীয় সরঞ্জাম:

স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
মেশিন ভাইসমেশিন ভাইস
ড্রিল-বিট সেটড্রিল-বিট সেট
প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
কাটার তেলকাটার তেল
7

Make the screw and the guide pin

Turn the top 62 mm of a 90 mm piece of 10 mm bar to 8 mm and cut an M8 thread on it with the die. Turn a groove 1.5 mm deep and 3.2 mm wide in the plain part, where the cross pin will sit, and drill a 6 mm hole across its bottom end for a T-bar. Cut the guide pin, 80 mm of 6 mm rod, and drill a 3 mm hole across its top for the stop pin.

এই ধাপের উপকরণ:

নরম ইস্পাতের গোল দণ্ডনরম ইস্পাতের গোল দণ্ড1 টুকরা
নরম ইস্পাতের গোল দণ্ডনরম ইস্পাতের গোল দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
তিন-চোয়ালের খরাদ চাকতিন-চোয়ালের খরাদ চাক
খরাদের কাটার যন্ত্রখরাদের কাটার যন্ত্র
কাটার ছেনি (খরাদ)কাটার ছেনি (খরাদ)
প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেটড্রিল-বিট সেট
হ্যাকসহ্যাকস
ডিজিটাল ক্যালিপার ৬ ইঞ্চিডিজিটাল ক্যালিপার ৬ ইঞ্চি
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

এই ধাপের উপকরণ:

যন্ত্র-ইস্পাতের দণ্ডযন্ত্র-ইস্পাতের দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
তিন-চোয়ালের খরাদ চাকতিন-চোয়ালের খরাদ চাক
খরাদের কাটার যন্ত্রখরাদের কাটার যন্ত্র
কাটার ছেনি (খরাদ)কাটার ছেনি (খরাদ)
সেন্টার ড্রিল সেটসেন্টার ড্রিল সেট
ড্রিল-বিট সেটড্রিল-বিট সেট
ডিজিটাল ক্যালিপার ৬ ইঞ্চিডিজিটাল ক্যালিপার ৬ ইঞ্চি
সুরক্ষা চশমাসুরক্ষা চশমা
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

প্রয়োজনীয় সরঞ্জাম:

কামারের ভাটিকামারের ভাটি
কামারের সাঁড়াশিকামারের সাঁড়াশি
ছোট চুম্বকছোট চুম্বক
জল দেওয়ার বালতিজল দেওয়ার বালতি
জলজল
শান দেওয়ার পাথরশান দেওয়ার পাথর
ঝালাইয়ের দস্তানাঝালাইয়ের দস্তানা
সুরক্ষা চশমাসুরক্ষা চশমা
10

Assemble

Drive the guide pin into the stationary jaw. Put the screw into its hole from below and drive the cross pin in so it lies in the groove; the screw must still turn. Fit the T-bar. Slip the spring over the guide pin, then the movable jaw over the pin and the screw, and put the stop pin across the top. Fit the wheel in the support on its 5 mm pin, and pin the support into the jaw with its pivot and stop pins. Rivet a 1.5 mm steel strip along the top of the jaw, sticking out past the support as a thumb piece. Oil the threads.

এই ধাপের উপকরণ:

ইস্পাতের ডাউল পিনইস্পাতের ডাউল পিন5 টুকরা
সংনমন স্প্রিং সেটসংনমন স্প্রিং সেট1 টুকরা
স্প্রিং ইস্পাতের ফালিস্প্রিং ইস্পাতের ফালি1 টুকরা
ইস্পাতের রিভেটইস্পাতের রিভেট2 টুকরা
নরম ইস্পাতের গোল দণ্ডনরম ইস্পাতের গোল দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

গোল মাথার হাতুড়িগোল মাথার হাতুড়ি
কেন্দ্র-ছিদ্রককেন্দ্র-ছিদ্রক
বেঞ্চ ভাইসবেঞ্চ ভাইস
স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেটড্রিল-বিট সেট
কাটার তেলকাটার তেল
11

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Swing the support down, push the movable jaw down until the wheel touches the tube in the V, swing it up into the screw, and tighten the screw a little. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

এই ধাপের উপকরণ:

তামার নলতামার নল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

বেঞ্চ ভাইসবেঞ্চ ভাইস
ছাঁট তোলার যন্ত্রছাঁট তোলার যন্ত্র
ডিজিটাল ক্যালিপার ৬ ইঞ্চিডিজিটাল ক্যালিপার ৬ ইঞ্চি
12

Troubleshooting

Swing-nut tubing cutter troubleshooting.

Flow

Loading...
13

History and honest limits

**Frank L. Pritchard** of Parker, Arizona, US 2,231,593, dated 11 February 1941, filed 17 November 1939. He claimed "a pivoted blade support mounted on the movable jaw and having threads on the inner edge thereof adapted to engage the threads of said screw". His movable jaw had a bushing for the guide pin and a looped handle on the screw head; ours has a drilled hole and a T-bar. The patent gives no sizes or materials; all of ours are ours.

উপকরণ

9

প্রয়োজনীয় সরঞ্জাম

27

ডিজাইন ফাইল

1

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...