সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Small Series-Wound Electric Motor with Laminated Field and 12-Slot Ring Armature (Robertson, Boy Mechanic 1913)
Volt

তৈরি করেছেন

Volt

14. নভেম্বর 2026SE
৯
০
০
০
০

Small Series-Wound Electric Motor with Laminated Field and 12-Slot Ring Armature (Robertson, Boy Mechanic 1913)

A real workshop-built DC motor: a field of riveted sheet-iron plates bored to 2-3/4 in, a 12-slot laminated ring armature on a brass spider, a 12-segment brass commutator insulated with mica, gauze brushes, and series windings of cotton-covered magnet wire.
উন্নত
Several weekends

নির্দেশাবলি

1

Read the Boy Mechanic

"The field frame of the motor, Fig. 1, is composed of wrought sheet iron."
2

Field frame

Mark a template 1/16 in larger than Fig. 1, cut enough sheet-iron plates to make 3/4 in, drill four rivet holes and rivet them. Mark the bore with dividers set at 1/8 in, drill 1/4 in holes round it and file to shape. Bore to 2-3/4 in on a lathe; mark the field core at 3-3/8 in and the outside at 4-1/2 in and finish to the marks.

এই ধাপের উপকরণ:

নরম ইস্পাতের পাতনরম ইস্পাতের পাত1 টুকরা
ইস্পাতের রিভেটইস্পাতের রিভেট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

দাগ টানার শলাকাদাগ টানার শলাকা
দুই ফলাযুক্ত কম্পাসদুই ফলাযুক্ত কম্পাস
হাত-ড্রিলহাত-ড্রিল
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
হাতুড়িহাতুড়ি
3

Studs, lugs and bearings

Drill and tap two 3/8 in holes 3-5/8 in apart for the bearing studs (Fig. 2) and 1/4 in holes for feet bent from 1/8 in brass or iron. Make the bearing supports from 1/8 in brass with a 5/8 in hole and a 5/8 in brass rod soldered in and drilled for the shaft. Fit them after the armature is made: wrap paper round the armature, set it in the field, slip the bearings on and solder them, then check it turns freely.

এই ধাপের উপকরণ:

পিতলের পাতপিতলের পাত1 টুকরা
পিতলের দণ্ডপিতলের দণ্ড1 টুকরা
নরম ইস্পাতের গোল দণ্ডনরম ইস্পাতের গোল দণ্ড1 টুকরা
টিন-সিসার ঝালাইটিন-সিসার ঝালাই1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
ঝালাইয়ের ছড়ঝালাইয়ের ছড়
হাত-ড্রিলহাত-ড্রিল
4

Armature core

Cut two 1/8 in wrought-iron outer plates and enough No. 24 sheet iron to make over 3/4 in (Fig. 5), drill six 1/8 in holes and rivet. Anneal at cherry red and cool in ashes. Bore to 1-11/16 in, fit a brass spider turned from 3/4 in brass on the machine-steel shaft with a setscrew, solder, turn the outside and face it to 3/4 in. File 12 slots 1/4 in deep and 7/16 in wide.

এই ধাপের উপকরণ:

নরম ইস্পাতের পাতনরম ইস্পাতের পাত1 টুকরা
ইস্পাতের রিভেটইস্পাতের রিভেট1 টুকরা
পিতলের দণ্ডপিতলের দণ্ড1 টুকরা
নরম ইস্পাতের গোল দণ্ডনরম ইস্পাতের গোল দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

কামারের ভাটিকামারের ভাটি
ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
হাত-ড্রিলহাত-ড্রিল
5

Commutator

Turn a piece of 3/4 in i.d. brass pipe to 3/4 in long, chamfer both ends at 60 deg, divide into 12, drill and tap a 1/8 in hole in each segment for a brass pin, turn the pins to 1-1/4 in outside and slit them for the wires. Saw it into 12 bars, fit them on turned fibre ends with 12 mica strips between, clamp with the nut and true up.

এই ধাপের উপকরণ:

পিতলের নলপিতলের নল1 টুকরা
পিতলের দণ্ডপিতলের দণ্ড1 টুকরা
ভালকানাইজড ফাইবার শিটভালকানাইজড ফাইবার শিট1 টুকরা
অভ্রের পাতঅভ্রের পাত1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
প্যাঁচ কাটার সেটপ্যাঁচ কাটার সেট
হ্যাকসহ্যাকস
6

Brushes

Make the brush holder of fibre (Fig. 8) and studs of 5/16 in brass rod (Fig. 9). Roll brass or copper wire gauze and flatten it to 1/8 x 1/4 in, solder one end, and fit the holder on the bearing with a setscrew.

এই ধাপের উপকরণ:

ভালকানাইজড ফাইবার শিটভালকানাইজড ফাইবার শিট1 টুকরা
পিতলের দণ্ডপিতলের দণ্ড1 টুকরা
তারের জালতারের জাল1 টুকরা
টিন-সিসার ঝালাইটিন-সিসার ঝালাই1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ঝালাইয়ের ছড়ঝালাইয়ের ছড়
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
7

Wind the field

Insulate the field cores with 1/64 in fibre and end washers 1-1/8 x 1-1/2 in (softened in warm water, then glued). Wind each side with four layers (about 50 ft) of No. 18 double-cotton-covered wire, A to B and C to B, and join the ends at B.

এই ধাপের উপকরণ:

ভালকানাইজড ফাইবার শিটভালকানাইজড ফাইবার শিট1 টুকরা
এনামেল-মোড়া তামার তারএনামেল-মোড়া তামার তার1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
8

Wind the armature

Line the ring and spider with 1/16 in fibre and the slots with 1/64 in fibre channels. Wind each slot with about 12 ft of No. 21 wire, 40 turns in four layers of 10, shellacking each layer, leaving 2 in ends. Join each coil's start to the next coil's finish and solder the joints to the commutator pins.

এই ধাপের উপকরণ:

ভালকানাইজড ফাইবার শিটভালকানাইজড ফাইবার শিট1 টুকরা
এনামেল-মোড়া তামার তারএনামেল-মোড়া তামার তার1 টুকরা
শেলাকের বার্নিশশেলাকের বার্নিশ1 টুকরা
টিন-সিসার ঝালাইটিন-সিসার ঝালাই1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ঝালাইয়ের ছড়ঝালাইয়ের ছড়
9

Mount and wire

Screw the motor to a wood base 8 x 6 x 1 in with two terminals and a switch. Wire it in series: field end A to a terminal, field end C to one brush stud, the other brush through the switch to the other terminal.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
বাইন্ডিং পোস্টবাইন্ডিং পোস্ট1 টুকরা
টগল সুইচটগল সুইচ1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
10

Troubleshooting

Motor troubleshooting.

Flow

Loading...
11

History and honest limits

From W. A. Robertson in **The Boy Mechanic, Book 1** (Popular Mechanics, 1913), pp. 345-347 (checked on the archive.org scan boymechanic0000unse_n5a8). Sizes not in the text are in his Figs. 1-9; enamelled wire for cotton-covered and the low-voltage advice are ours.

উপকরণ

17

প্রয়োজনীয় সরঞ্জাম

11

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...