সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)
Forge

তৈরি করেছেন

Forge

13. নভেম্বর 2026NO
৯
০
০
০
০

Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)

Howard S. Root of Spokane received US 2,631,224, dated 10 March 1953, for a safe light for jack-o'-lanterns: "The most common device is an ordinary candle. That, however, is very dangerous." A springy tin clip holds a dry cell; a bulb screwed into a hinged tin support rests on the top of the cell, and the clip itself carries the current back from the bottom. A wire handle through the lid lifts the bulb to switch it off. We bend it from tinplate and fit it in a carved pumpkin. All sizes are ours.
শিক্ষানবিশ
About 2 hours

নির্দেশাবলি

1

Bracket blank

Jupyter নোটবুক লোড হচ্ছে…
2

Read US 2,631,224

"I provide an operating means for the light bulb support 18 of such a nature that the child can turn the light on and off at will, yet if the entire toy is carried by the operating handle, no harm is done to the device."
3

Bend the cell clip

Cut the tinplate strip from the notebook. Bend it into a U round the cell, his container 10: the bottom is the cross bar 10c, the sides are legs 10a and 10b. Curve the legs a little across their width so the cell cannot slide out sideways, and snip and press in a small tongue on each leg (his 15) to grip it. Snip two pointed fingers at the bottom (his 13).

এই ধাপের উপকরণ:

টিন-মোড়া পাতটিন-মোড়া পাত1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

পাত কাটার কাঁচিপাত কাটার কাঁচি
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
4

Make the bulb support

Cut a tin plate a little longer than the cell is wide, his support 18. Punch a hole in the middle just big enough for the bulb's screw base to screw into (his threaded aperture 19; ours). Bend two small ears at the top of leg 10a (his 21) and roll the support's end round a wire pin (22) between them, so it hinges.

এই ধাপের উপকরণ:

টিন-মোড়া পাতটিন-মোড়া পাত1 টুকরা
স্প্রিং ইস্পাতের তারস্প্রিং ইস্পাতের তার1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

পাত কাটার কাঁচিপাত কাটার কাঁচি
কেন্দ্র-ছিদ্রককেন্দ্র-ছিদ্রক
গোল মুখের সাঁড়াশিগোল মুখের সাঁড়াশি
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
5

Fit the spring and handle

Wind a few turns of spring wire on the hinge pin, one end hooked over the top of leg 10a and the other over the support, so it presses the support down (his spring 25). Bend a wire handle (his 20) long enough to come out of the top opening; pivot its lower end in a turned-over tab on leg 10b (26) and bend a short arm (27) under the free end of the support, so raising the handle lifts the bulb.

এই ধাপের উপকরণ:

স্প্রিং ইস্পাতের তারস্প্রিং ইস্পাতের তার1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

গোল মুখের সাঁড়াশিগোল মুখের সাঁড়াশি
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
তেরছা তার কাটার প্লায়ারতেরছা তার কাটার প্লায়ার
6

Put in the cell and bulb

Seat the cell with its centre terminal down on the cross bar, put a tin band (his 16) round the legs if they are loose, and screw the bulb into the support. Let the support down: the bulb's end terminal should touch the top of the cell and light, the current returning through the support, the hinge and the clip.

এই ধাপের উপকরণ:

শুষ্ক কোষশুষ্ক কোষ1 টুকরা
টর্চের বাল্বটর্চের বাল্ব1 টুকরা
টিন-মোড়া পাতটিন-মোড়া পাত1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

পাত কাটার কাঁচিপাত কাটার কাঁচি
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
7

Fit it in the pumpkin

Carve the pumpkin's face and cut the top opening (ours; his toys are hollow figures). Push the clip's fingers through the bottom of the pumpkin, put a washer over them outside, and bend them over it (his washer 8), so the light stands in the middle. Pass the handle up through the top opening.

এই ধাপের উপকরণ:

কুমড়োকুমড়ো1 টুকরা
সমতল ওয়াশারসমতল ওয়াশার1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

কারুকাজের ছুরিকারুকাজের ছুরি
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
8

Use it

Lower the handle and the bulb lights; raise it and the light goes off. To change the cell, lift the support and take the cell out.
9

Troubleshooting

Jack-o'-lantern light troubleshooting.

Flow

Loading...
10

History and honest limits

**Howard S. Root** of Spokane, Washington, US 2,631,224, dated 10 March 1953, filed 21 December 1948. He claimed "an illuminated figure toy comprising a hollow body having an opening in the top thereof", a conductive container for a dry cell, a hinged conductive bulb support, and spring means pressing the bulb's end terminal against the cell. He also shows other hinges, a magnet latch and a side handle (Figs. 6-13), not built here. He gives no sizes or materials: the tinplate, all sizes, the pumpkin and the cell and bulb are ours.

উপকরণ

6

প্রয়োজনীয় সরঞ্জাম

6

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...