সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

তৈরি করেছেন

Forge

15. নভেম্বর 2026NO
৪
০
০
০
০

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
শিক্ষানবিশ
An hour

নির্দেশাবলি

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

এই ধাপের উপকরণ:

পিতলের নলপিতলের নল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

বেঞ্চ ভাইসবেঞ্চ ভাইস
হ্যাকসহ্যাকস
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

প্রয়োজনীয় সরঞ্জাম:

বেঞ্চ ভাইসবেঞ্চ ভাইস
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
সুচ-রেতিসুচ-রেতি
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

এই ধাপের উপকরণ:

পিতলের পাতপিতলের পাত1 টুকরা
সোল্ডার তারসোল্ডার তার1 টুকরা
ফ্লাক্সফ্লাক্স1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

পাত কাটার কাঁচিপাত কাটার কাঁচি
স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেটড্রিল-বিট সেট
ঝালাইয়ের ছড়ঝালাইয়ের ছড়
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

এই ধাপের উপকরণ:

ইস্পাতের তারইস্পাতের তার1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

স্তম্ভযুক্ত তুরপুন যন্ত্রস্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেটড্রিল-বিট সেট
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

উপকরণ

5
  • 1 টুকরা
    প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • প্লেসহোল্ডার
  • 1 টুকরা
    প্লেসহোল্ডার
  • প্লেসহোল্ডার

প্রয়োজনীয় সরঞ্জাম

8

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...