সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)
Forge

তৈরি করেছেন

Forge

4. নভেম্বর 2026NO
১৩
০
০
০
০

Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)

The Paris method of Rouy and Berthier: thin sheet-iron discs, red-hot, punched step by step into a cup through five ever-deeper hollows, then turned, pitted and annealed on the lathe, gilt inside with gold leaf pressed on by a steel mandril, and banded outside with a gold fillet. Variable: closed (pitted round end) or open (no end, for tailors). Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Thimble'. Picture: a modern pitted thimble (Commons, CC BY-SA 3.0).
উন্নত
Unknown

নির্দেশাবলি

1

Punch the blanks

Cut sheet iron 1/24 in thick into strips sized for the thimbles. Run them under a punch press to cut discs about 2 in across, left joined by a tail, a dozen to a strip.

এই ধাপের উপকরণ:

লোহার পাত (হাতুড়ি-পেটা)লোহার পাত (হাতুড়ি-পেটা)1 1/24 in

প্রয়োজনীয় সরঞ্জাম:

পাঞ্চ প্রেসপাঞ্চ প্রেস
2

Sink the cup

Heat the blanks red-hot and lay each on a mandril fitted to its size. Strike the middle with a round-faced punch about as thick as a finger to sink it into the first hollow, then drive it through a block with five hollows of increasing depth until it has the thimble's shape.

প্রয়োজনীয় সরঞ্জাম:

কামারের ভাটিকামারের ভাটি
চিমটাচিমটা
অজানা ধাতুঅজানা ধাতু
হাতুড়িহাতুড়ি
3

Turn and pit on the lathe

Chuck the rough thimble in the lathe, polish the inside, turn the outside, mark the rings for the gold band, and press in the rows of pits with a milling tool.

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
নার্লিং যন্ত্রনার্লিং যন্ত্র
4

Anneal, gild and band

Anneal and brighten the thimbles. Line each inside with a thin cone of gold leaf, bonded to the iron by the hard pressure of a smooth steel mandril. Turn an annular seat outside, lay a gold fillet in it and press its edges into a fine groove cut on the lathe.

এই ধাপের উপকরণ:

সোনার পাতসোনার পাত1 lining
অজানা ধাতুঅজানা ধাতু1 gold fillet

প্রয়োজনীয় সরঞ্জাম:

কামারের ভাটিকামারের ভাটি
খরাদের ভিতরের দণ্ডখরাদের ভিতরের দণ্ড
ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র

উপকরণ

3

প্রয়োজনীয় সরঞ্জাম

8

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...