সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Three-Piece Airlock, 3D Printed in PETG
3DBonanza

তৈরি করেছেন

3DBonanza

18. নভেম্বর 2026US
১
০
০
১
০

Three-Piece Airlock, 3D Printed in PETG

An airlock lets the carbon dioxide of a fermenting beer, wine or cider out through a little water, and keeps outside air out. This one has the four parts of the "standard type device" named in L. P. Beadle's 1980 US patent 4,218,964: a cap, a tapered stem, a housing two-thirds full of water, and a cone member. It prints in three pieces in PETG. All sizes are ours, and we have not printed or tested it yet: the leak test below comes first.
শিক্ষানবিশ
About 5 hours, mostly printing

নির্দেশাবলি

1

Seal pressure and water back-flow

Jupyter নোটবুক লোড হচ্ছে…
2

Read US 4,218,964

"Housing 27 is filled two-thirds full with water, cone 28 is inserted and cap 25 is secured ... excess gas escapes by bubbling through the water in lock 14 so as to protect the beer ingredients within container 11 from contact with outside air." The picture is our section: gas goes up the stem, under the cone member's rim and out of the cap.
ধাপ 2 - Image 1
3

Print the housing and stem

Stand it on the stem's tip with a 10 mm brim; the 45 degree cone under the floor needs no supports. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
নকশা ফাইলSTLCC0 - Free

এই ধাপের উপকরণ:

PETG ফিলামেন্টPETG ফিলামেন্ট15 গ্রা

প্রয়োজনীয় সরঞ্জাম:

ফিলামেন্টের 3D প্রিন্টার (FDM)ফিলামেন্টের 3D প্রিন্টার (FDM)
3D প্রিন্টার নজল সেট3D প্রিন্টার নজল সেট
4

Print the cone member

Print it upside down, closed end on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
নকশা ফাইলSTLCC0 - Free

এই ধাপের উপকরণ:

PETG ফিলামেন্টPETG ফিলামেন্ট3 গ্রা

প্রয়োজনীয় সরঞ্জাম:

ফিলামেন্টের 3D প্রিন্টার (FDM)ফিলামেন্টের 3D প্রিন্টার (FDM)
3D প্রিন্টার নজল সেট3D প্রিন্টার নজল সেট
5

Print the cap

Print it upside down, top on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
নকশা ফাইলSTLCC0 - Free

এই ধাপের উপকরণ:

PETG ফিলামেন্টPETG ফিলামেন্ট3 গ্রা

প্রয়োজনীয় সরঞ্জাম:

ফিলামেন্টের 3D প্রিন্টার (FDM)ফিলামেন্টের 3D প্রিন্টার (FDM)
3D প্রিন্টার নজল সেট3D প্রিন্টার নজল সেট
6

Clean the parts

Take off the brim. Turn a 5 mm drill bit through the stem by hand to clear any strings. Check the stem: 10.0 mm at the top, 8.5 mm at the tip.

প্রয়োজনীয় সরঞ্জাম:

ড্রিল-বিট সেটড্রিল-বিট সেট
ডিজিটাল ক্যালিপার ৬ ইঞ্চিডিজিটাল ক্যালিপার ৬ ইঞ্চি
7

Leak test

Fill the housing with water to the groove. Stand it in a dry glass for an hour. Any drop on the outside or in the glass means a leak: print again.

প্রয়োজনীয় সরঞ্জাম:

জলজল
8

Sanitise

Soak all three parts in no-rinse sanitiser mixed as its label says. Do not boil them: PETG softens at about 80 °C.

প্রয়োজনীয় সরঞ্জাম:

জীবাণুনাশকজীবাণুনাশক
জলজল
9

Assemble and fill

Drop the cone member over the riser tube. Fill the housing to the groove with sanitiser solution, not plain water. Push the cap on.

প্রয়োজনীয় সরঞ্জাম:

জীবাণুনাশকজীবাণুনাশক
জলজল
10

Fit it to the fermenter

Push the stem into the bored stopper or the lid's hole. The stem gets thinner towards the tip, so it wedges tight, as in Beadle's patent. Gas must bubble through the water, never round the stem.

প্রয়োজনীয় সরঞ্জাম:

রবারের ছিপিরবারের ছিপি
11

Troubleshooting

Airlock problems and fixes.

Flow

Loading...
12

History and honest limits

**Leigh P. Beadle**, US 4,218,964, "Lid construction for fermentation container", filed 21 May 1979, issued 26 August 1980, assigned to Specialty Products International Ltd. His invention was the lid; he calls the airlock "a standard type device" and names its parts: cap 25, tapered stem 26, housing 27 and cone member 28. He gives no sizes and no material for the lock. Ours: every size, the riser tube, the three ribs, the vent holes, the posts that stop the cone member lifting more than 3.4 mm, and PETG. Checked in CAD for fit; not yet printed or brewed with by us.

উপকরণ

1

প্রয়োজনীয় সরঞ্জাম

7

ডিজাইন ফাইল

3

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...