সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle.
Painted red inside and light green outside, lined in a lighter colour and black.
Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
মধ্যবর্তী
Unknown
নির্দেশাবলি
1
1
Make the hales
Make the hales
Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.
এই ধাপের উপকরণ:
অ্যাশ কাঠের তক্তা1 hales 3 ft 1 in x 1 5/8 x 1 1/2 inপ্রয়োজনীয় সরঞ্জাম:
হাত-করাত
রান্দা
দুই হাতলের রান্দা2
2
Frame with oak cross-pieces
Frame with oak cross-pieces
Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.
এই ধাপের উপকরণ:
সাদা ওকের তক্তা1 টুকরা
কাঠের খিল1 3/16 in pinsপ্রয়োজনীয় সরঞ্জাম:
পিঠ-দণ্ডযুক্ত করাত
খাঁজ কাটার বাটালি
দাগ কাটার গেজ
হাতে ঘোরানো তুরপুন ও ফলা
সমন্বয়যোগ্য কোণমাপক3
3
Fit the legs and stays
Fit the legs and stays
Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.
এই ধাপের উপকরণ:
সাদা ওকের তক্তা1 legs 1 1/2 in square, stays
গোল মাথার বোল্ট4 3 inপ্রয়োজনীয় সরঞ্জাম:
হাত-করাত
হাতে ঘোরানো তুরপুন ও ফলা
স্ক্রুড্রাইভার সেট4
4
Bottom and sides
Bottom and sides
Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.
এই ধাপের উপকরণ:
পাইন কাঠের তক্তা1 1/2 in bottom, 5/8 in sides
তৈলরং1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হাত-করাত
রান্দা
তুলির সেট5
5
Front board and ironwork
Front board and ironwork
Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.
এই ধাপের উপকরণ:
পাইন কাঠের তক্তা1 3/4 in front board
লোহার পেরেক1 1 1/2 in cut nails
নরম ইস্পাতের চ্যাপ্টা পাটা1 7/8 in hoop iron
কাঠের স্ক্রু1 3/4 in round-headed
তৈলরং1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হাত-করাত
হাতুড়ি
স্ক্রুড্রাইভার সেট
তুলির সেট6
6
Make the wheel
Make the wheel
Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.
এই ধাপের উপকরণ:
অ্যাশ কাঠের তক্তা1 axle and felloes
সাদা ওকের তক্তা1 spokes
লোহার শলা1 3/8 in pins
কাঠের খিল4 1/4 in
নরম ইস্পাতের চ্যাপ্টা পাটা1 3/4 x 1/8 in tyreপ্রয়োজনীয় সরঞ্জাম:
কাঠের লেদ
দুই হাতলের রান্দা
হাতে ঘোরানো তুরপুন ও ফলা
হাতুড়ি7
7
Hang the wheel and paint
Hang the wheel and paint
Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.
এই ধাপের উপকরণ:
নরম ইস্পাতের চ্যাপ্টা পাটা2 3/4 x 1/8 in irons
কাঠের স্ক্রু1 টুকরা
তৈলরং1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
স্ক্রুড্রাইভার সেট
তুলির সেটউপকরণ
10- 1 axle and felloesপ্লেসহোল্ডার
- 1 spokesপ্লেসহোল্ডার
- 4 1/4 inপ্লেসহোল্ডার
- 4 3 inপ্লেসহোল্ডার
- 1 3/4 in front boardপ্লেসহোল্ডার
- 3 টুকরাপ্লেসহোল্ডার
- 1 1 1/2 in cut nailsপ্লেসহোল্ডার
- 2 3/4 x 1/8 in ironsপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 3/8 in pinsপ্লেসহোল্ডার
প্রয়োজনীয় সরঞ্জাম
12- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
এই ব্লুপ্রিন্ট যা তৈরি করে
CC0 পাবলিক ডোমেন
এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।
মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।
