সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
মধ্যবর্তী
A day
নির্দেশাবলি
1
1
The steps
The steps
Jupyter নোটবুক লোড হচ্ছে…
2
2
Read Willey
Read Willey
"A very efficient, quick-opening and closing vise for the drill-press table."
3
3
Make the bed
Make the bed
Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.
এই ধাপের উপকরণ:
নরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
কেন্দ্র-ছিদ্রক
স্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেট4
4
Make the end supports
Make the end supports
Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.
এই ধাপের উপকরণ:
নরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
ষড়ভুজ বোল্টের সংগ্রহ1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
স্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেট
রেতি (হাতের রেতি)5
5
Make the fixed jaw
Make the fixed jaw
Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.
এই ধাপের উপকরণ:
নরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
নরম ইস্পাতের গোল দণ্ড1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
রেতি (হাতের রেতি)
স্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেট
গোল মাথার হাতুড়ি6
6
Make the sliding jaw
Make the sliding jaw
Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.
এই ধাপের উপকরণ:
নরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
নরম ইস্পাতের গোল দণ্ড1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
রেতি (হাতের রেতি)
স্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেট
গোল মাথার হাতুড়ি
বেঞ্চ ভাইস7
7
Make the cam
Make the cam
Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.
এই ধাপের উপকরণ:
ইস্পাতের শ্যাফট1 টুকরা
নরম ইস্পাতের গোল দণ্ড1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
স্তম্ভযুক্ত তুরপুন যন্ত্র
ড্রিল-বিট সেট
গোল মাথার হাতুড়ি8
8
Use it
Use it
Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.
এই ধাপের উপকরণ:
ষড়ভুজ বোল্টের সংগ্রহ1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
স্তম্ভযুক্ত তুরপুন যন্ত্র9
9
Troubleshooting
Troubleshooting
Drill vise troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.
উপকরণ
4- 1 টুকরাপ্লেসহোল্ডার
- 2 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
এই ব্লুপ্রিন্ট যা তৈরি করে
সম্পর্কিত ব্লুপ্রিন্ট
এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি
CC0 পাবলিক ডোমেন
এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।
মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।


