সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Workbench: a Pine Bench with a Plank Top and Vise (Boy Mechanic, 1913)
Woody

তৈরি করেছেন

Woody

4. নভেম্বর 2026NO
১১
০
০
০
০

Workbench: a Pine Bench with a Plank Top and Vise (Boy Mechanic, 1913)

A boy's first workshop bench: two mortised pine leg frames bolted to braces, a 3 1/2 ft top of one 2 x 12 in plank with a back board, a tool rack behind, and a wooden vise on an iron bench screw. Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
মধ্যবর্তী
Unknown

নির্দেশাবলি

1

Make the two leg frames

Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.

এই ধাপের উপকরণ:

পাইন কাঠপাইন কাঠ1 2 x 4 in: legs, crosspieces

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
খাঁজ কাটার বাটালিখাঁজ কাটার বাটালি
হাতুড়িহাতুড়ি
2

Brace them together

Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.

এই ধাপের উপকরণ:

পাইন কাঠপাইন কাঠ1 2 x 4 in: braces
গোল মাথার বোল্টগোল মাথার বোল্ট4 3/8 x 6 in

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
3

Fit the plank top

Make the main top M from one 2 x 12 in plank 3 1/2 ft long. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.

এই ধাপের উপকরণ:

শক্ত কাঠের মোটা তক্তাশক্ত কাঠের মোটা তক্তা1 2 x 12 in, 3 1/2 ft
পাইন কাঠের তক্তাপাইন কাঠের তক্তা1 back board
কাঠের স্ক্রুকাঠের স্ক্রু1 long

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
ব্লক রাঁদাব্লক রাঁদা
স্ক্রুড্রাইভার - চ্যাপ্টাস্ক্রুড্রাইভার - চ্যাপ্টা
4

Add the tool rack

Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.

এই ধাপের উপকরণ:

পাইন কাঠের তক্তাপাইন কাঠের তক্তা2 7/8 in, 3 1/2 ft
পেরেকপেরেক1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
হাত-করাতহাত-করাত
হাতুড়িহাতুড়ি
5

Fit the vise

Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).

এই ধাপের উপকরণ:

পাইন কাঠপাইন কাঠ1 2 x 6 block, 2 x 4 pieces, guide rails
কাঠ খোদাইয়ের বেঞ্চের স্ক্রুকাঠ খোদাইয়ের বেঞ্চের স্ক্রু1 টুকরা
গোল মাথার বোল্টগোল মাথার বোল্ট1 for L and P
পেরেকপেরেক1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
খাঁজ কাটার বাটালিখাঁজ কাটার বাটালি
হাতে ঘোরানো তুরপুন ও ফলাহাতে ঘোরানো তুরপুন ও ফলা
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
হাতুড়িহাতুড়ি

উপকরণ

7

প্রয়োজনীয় সরঞ্জাম

7

এই ব্লুপ্রিন্ট যা তৈরি করে

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...