སྒྱུ་རྩལ
མཛེས་སྡུག་དང་བདེ་ཐང
བཟོ་རིག
རིག་གནས་དང་ལོ་རྒྱུས
དགའ་སྟོན
ཁོར་ཡུག
ཟས་དང་བཏུང་རྫས
ཕྱིར་འཕྲུལ་རིག
ཚན་རིག
རྩེད་འགྲན
རིག་རྩལ
གྱོན་རུང
Copper Wire Drawn Through a Drawplate
Forge

བཟོས་མཁན

Forge

11. སྤྱི་ཟླ་བཅུ་པ 2026NO
༣༦
༠
༠
༠
༠

Copper Wire Drawn Through a Drawplate

Wire is pulled, not rolled: a tapered rod is drawn through a hardened steel plate with a row of shrinking holes, one hole at a time, getting thinner and longer each pass. Drawing hardens copper, so it is annealed every few holes. Jewellers and electricians' forebears made all their wire this way.
བར་མ
Half a day

ལམ་སྟོན

1

Make a rod

Forge cast copper into a round rod a little larger than the drawplate's largest hole, annealing as it stiffens.

གོམ་པ་འདིའི་རྫས་རིགས:

ཟངས་ཀྱི་ཐུར་གོངཟངས་ཀྱི་ཐུར་གོང100 g
ཆུ།ཆུ།10 ལི་ཊར།

ལག་ཆས་དགོས་མཁོ:

མགར་བའི་རྡོ་ལེབ།མགར་བའི་རྡོ་ལེབ།
རྒྱབ་ཐིག་གི་ཐོ་བ།རྒྱབ་ཐིག་གི་ཐོ་བ།
པོ་རོ་པེན་གྱི་མེ་ལྕེ།པོ་རོ་པེན་གྱི་མེ་ལྕེ།
མགར་བའི་ལག་བཟུང་།མགར་བའི་ལག་བཟུང་།
སྲ་བཟོའི་ཆུ་སྣོད།སྲ་བཟོའི་ཆུ་སྣོད།
2

Taper the end

File the first 2 cm of the rod to a long taper so it pokes through the hole.

ལག་ཆས་དགོས་མཁོ:

དར་མའི་ཚོགས་ཆས།དར་མའི་ཚོགས་ཆས།
ལས་ཅོག་གི་འཛིན་ཆས།ལས་ཅོག་གི་འཛིན་ཆས།
3

Set up the plate

Clamp the drawplate in the vise with its tapered side facing you. Rub beeswax on the rod as lubricant.

གོམ་པ་འདིའི་རྫས་རིགས:

སྦྲང་ཞུན།སྦྲང་ཞུན།5 g

ལག་ཆས་དགོས་མཁོ:

ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།
ལས་ཅོག་གི་འཛིན་ཆས།ལས་ཅོག་གི་འཛིན་ཆས།
4

Draw

Push the taper through the first hole that it does not slip through, grip it with the draw tongs and pull it through in one steady pull, straight out from the plate.

ལག་ཆས་དགོས་མཁོ:

འཐེན་ནིའི་ཀམ།འཐེན་ནིའི་ཀམ།
ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།ལྕགས་སྐུད་འཐེན་ནིའི་ལྕགས་ལེབ།
ཀོ་བའི་ལས་ལག་ཤུབས།ཀོ་བའི་ལས་ལག་ཤུབས།
5

Next holes, and anneal

Draw through each smaller hole in turn. Every three or four holes, coil the wire, anneal it to a dull red and quench.

ལག་ཆས་དགོས་མཁོ:

པོ་རོ་པེན་གྱི་མེ་ལྕེ།པོ་རོ་པེན་གྱི་མེ་ལྕེ།
མེ་ཐེག་སོ་ཕགམེ་ཐེག་སོ་ཕག
སྲ་བཟོའི་ཆུ་སྣོད།སྲ་བཟོའི་ཆུ་སྣོད།
6

Measure and coil

Stop at the size you need, measured with the caliper. Clean, coil and anneal for soft wire.

ལག་ཆས་དགོས་མཁོ:

ཨང་རྟགས་ཚད་འཇལ་ཆས་ ཨིནཅི 6ཨང་རྟགས་ཚད་འཇལ་ཆས་ ཨིནཅི 6
7

Troubleshooting

Wire drawing troubleshooting.

Flow

Loading...

རྫས་རིགས

3
  • ས་ཆ་འཛིན
  • 10 ལི་ཊར།
    ས་ཆ་འཛིན
  • ས་ཆ་འཛིན

ལག་ཆས་དགོས་མཁོ

12

CC0 སྤྱི་དབང

བིལུ་པིརིན་ཊི་འདི་CC0 འོག་བཀྲམས་ཡོད། ཁྱེད་རང་གིས་ཆོག་མཆན་མ་བཞེས་པར་ཕབ་ལེན་དང་བཟོ་བཅོས། བགོ་བཤའ། དགོས་མཁོ་གང་ལའང་བཀོལ་སྤྱོད་བྱས་ཆོག

བཟོ་མཁན་ལ་རྒྱབ་སྐྱོར་བྱེད་པའི་ཆེད་ཁོང་ཚོའི་བིལུ་པིརིན་ཊི་བརྒྱུད་ཐོན་སྐྱེད་ཉོ། བཟོ་མཁན་གྱིས བཟོ་མཁན་གྱི་ཁེ་ཕོགས ཚོང་པས་གཏན་འཁེལ་བྱས་པ། ཡང་ན་བིལུ་པིརིན་ཊི་འདིའི་པར་གསར་བཟོས་ཏེ་ཁྱེད་རང་གི་བིལུ་པིརིན་ཊི་ནང་མཐུད་སྦྲེལ་བྱས་ཏེ་ཡོང་སྒོ་བགོ་བཤའ་བྱེད།

གྲོས་བསྡུར

(0)

ནང་འཛུལ གྲོས་བསྡུར་ནང་མཉམ་ཞུགས་ཆེད

བསམ་ཚུལ་ཚུ་ཐོབ་བཞིན...