艺术
美容与健康
工艺
文化与历史
娱乐
环境
食品与饮料
逆向工程
科学
体育
技术
可穿戴设备
Air-Pump Tube Dasher: A Tube Over a Loose Plunger Pumps Air at Every Stroke
Wright wanted a hand dasher that "will operate as an air pump to force a stream of air into the cream at the same time that it agitates it."
William M. Wright of Pittsburgh, Pennsylvania, received US 6,711, dated 11 September 1849, for an atmospheric churn-dasher: a tube of tinned sheet iron with a flange on its lower end, a cap with a valve opening inward, and a handle; inside, a loose cylinder of wood weighted at its lower end rests on the bottom of the tub as a plunger. Worked like a common dasher in "almost any ordinary pail or dairy vessel," it discharges air among the cream on each descent and refills on each ascent.
This rung works out the air per stroke, then prints the cap, flange and plunger, assembles them on a pipe, and makes butter in a pail.
初学者
About 1 hour, plus printing
说明
1
1
Air per stroke
Air per stroke
正在加载 Jupyter 笔记本…
2
2
A dash closing over a fixed block before it
A dash closing over a fixed block before it
The embedded blueprint squeezes air from a hollow dash over a block fixed to the churn. Wright's plunger is loose, so it needs no fixing at all.
3
3
Read US 6,711
Read US 6,711
"From the fact of the piston resting loosely upon the bottom of the tub, and being capable of moving about and occupying a vertical or inclined position as may best suit the convenience of the operator, and also from the facility with which it and the dasher may be removed from the churn tub and cleaned, and from the simplicity of all the parts being a guarantee against their getting out of order, this apparatus is applicable to churning cream in either large or small quantities."
4
4
Print the parts
Print the parts
Print the cap (/uploads/blueprints/air-pump-tube-dasher-cap.stl) with its side valve port and handle socket, the foot flange (/uploads/blueprints/air-pump-tube-dasher-flange.stl), and the plunger (/uploads/blueprints/air-pump-tube-dasher-plunger.stl), whose foot has a pocket for a steel weight. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
此步骤所需材料：
PETG线材1 个所需工具：
FDM 3D 打印机5
5
Valve and weight
Valve and weight
Glue a small leather flap inside the cap over the valve port, along its top edge only, so air enters and cannot leave. Glue an M10 carriage bolt into the plunger's pocket, so it sinks in cream as he weighted his with metal.
此步骤所需材料：
皮条1 个
马车螺栓1 个
双组分环氧胶1 个所需工具：
螺丝刀套装6
6
Assemble
Assemble
Cut 300 mm of 50 mm pipe. Push the flange onto its foot and the cap onto its top, and glue a hardwood dowel handle in the cap's socket. Stand the plunger in a tall food-grade bucket and lower the tube over it.
此步骤所需材料：
PVC 管1 个
硬木销钉1 个
20 升水桶1 个双组分环氧胶1 个所需工具：
钢锯
砂纸7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the pail, tube and flange cut away to show the loose weighted plunger standing on the bottom inside the tube, the cap with its valve, and the handle.
8
8
Dash and make butter
Dash and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Work the tube up and down over the plunger; bubbles should burst from under the flange on each down-stroke. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
此步骤所需材料：
鲜奶油2000 毫升
粗海盐1 个
水1 个所需工具：
留置式探针温度计
秒表
数字厨房秤
大号不锈钢搅拌盆9
9
No bubbles, a plunger that floats
No bubbles, a plunger that floats
Air-pump tube dasher troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**William M. Wright** of Pittsburgh, Allegheny County, Pennsylvania, received US 6,711, dated 11 September 1849. The plunger was to be "specifically heavier than cream," or wood weighted with a plug of metal; the tub could be any pail, "particularly, if it be deep in comparison with its width." He claimed the combination of the loose plunger with the tubular dasher.
**Honest limits.** A pipe and printed parts stand in for his tinned sheet-iron tube; use a food-grade pipe. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
材料
10- 1 个占位符
- 1 个占位符
- 1 个占位符
- 2 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 2000 毫升占位符
- 1 个占位符
- 1 个占位符
此蓝图制作
相关蓝图
这些蓝图共享知识——技术、材料或原理
CC0 公共领域
此蓝图以 CC0 协议发布。你可以自由复制、修改、分发和使用此作品，无需征得许可。
通过购买蓝图中的产品支持创客，他们将获得 创客佣金 （由供应商设定），或创建此蓝图的新版本并将其作为连接包含在你自己的蓝图中以分享收入。