艺术
美容与健康
工艺
文化与历史
娱乐
环境
食品与饮料
逆向工程
科学
体育
技术
可穿戴设备
Interraking Plunger Churn: Two Rakes Worked Oppositely by a Double Crank
Schermerhorn did not claim churning with plungers, "either by hand, or by crank motion"; he claimed two of them shaped like rakes.
Jason B. Schermerhorn of Deerfield, New York, received US 3,616, dated 5 June 1844, for a dairy churn with "two rake-formed plungers with teeth interraking, and with oppositely reciprocating motions communicated to them by a cranked shaft." Standards on two sides of a square box carry the crank shaft; the teeth of one plunger pass between those of the other, "the one ascending while the other is descending," which "will produce a violent commotion in the cream."
This rung checks his proportions, then prints the rake heads, crank discs and yokes, builds the standards on a box, and makes butter.
中级
About 5 hours, plus printing
说明
1
1
His proportions
His proportions
正在加载 Jupyter 笔记本…
2
2
A double crank before it
A double crank before it
The embedded blueprint uses a double crank to pull two pitmen. Schermerhorn's double crank works two plungers up and down oppositely.
3
3
Read US 3,616
Read US 3,616
"The teeth of the plunger pass through the head piece horizontally, and at right angles therewith, projecting on both sides of the head-piece, but unequally; the projection on the side next the center of the churn being twice or thrice as great as on the other side. The length of the pieces forming the teeth should be equal to about two thirds of the width of the box."
4
4
Print the parts
Print the parts
Print two identical rake heads (/uploads/blueprints/interraking-plunger-churn-rake-head.stl): their teeth are set off-centre, so one turned round passes between the other's. Print two crank discs (/uploads/blueprints/interraking-plunger-churn-crank-disc.stl) and two yokes (/uploads/blueprints/interraking-plunger-churn-yoke.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
此步骤所需材料：
PETG线材1 个所需工具：
FDM 3D 打印机5
5
Box and standards
Box and standards
Take a food-safe box about 150 mm square and 200 mm deep. Screw a pine standard to each of two opposite sides, rising about 200 mm above the top, and drill both for a 10 mm square hardwood crank shaft. Cut two oblong openings in the lid for the plunger rods.
此步骤所需材料：
食品级贮存容器1 个
松木板1 个
#8 × 1 英寸木螺钉1 个所需工具：
手锯
充电式电钻
钻头套装
钢丝锯（曲线锯）
螺丝刀套装6
6
Crank and plungers
Crank and plungers
Slide the crank discs onto the shaft with their pins on opposite sides, half a turn apart, and glue them 60 mm apart. Glue a rake head on each of two 12 mm dowel rods, long sides of the teeth toward the centre, and a yoke on each rod's top. Pass the rods through the lid, hang the yokes on the crank pins, and glue the crank arm and a dowel handle on the shaft's end.
此步骤所需材料：
硬木销钉1 个
木工胶1 个所需工具：
手锯
砂纸7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the box cut away to show the two rake heads with their teeth interleaving, one at the bottom and one rising, their rods up to the two crank discs on the shaft between the standards, and the crank.
8
8
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1 litre, fit the lid, and crank steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
此步骤所需材料：
鲜奶油1000 毫升
粗海盐1 个
水1 个所需工具：
留置式探针温度计
秒表
数字厨房秤
大号不锈钢搅拌盆9
9
Teeth that clash, rods that bind
Teeth that clash, rods that bind
Interraking plunger churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Jason B. Schermerhorn** of Deerfield, Oneida County, New York, received US 3,616, dated 5 June 1844. His crank was a round iron rod "from one half to five-eighths of an inch in diameter" bent into a double crank "somewhat like a fulling mill crank"; the handles were forked over the cranks and pinned, so the plungers could be withdrawn; the tooth pieces might be one inch wide by half an inch.
**Honest limits.** Printed crank discs on a wooden shaft stand in for his bent iron crank, and a food-safe box for his wooden one. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
材料
9- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1000 毫升占位符
- 1 个占位符
- 1 个占位符
所需工具
11- 占位符
- 占位符
- 1 vendor sell this, none ship to you yet占位符
- 占位符
- 占位符
- 占位符
- 占位符
- 占位符
- 占位符
- 占位符
- 占位符
此蓝图制作
相关蓝图
这些蓝图共享知识——技术、材料或原理
CC0 公共领域
此蓝图以 CC0 协议发布。你可以自由复制、修改、分发和使用此作品，无需征得许可。
通过购买蓝图中的产品支持创客，他们将获得 创客佣金 （由供应商设定），或创建此蓝图的新版本并将其作为连接包含在你自己的蓝图中以分享收入。