艺术
美容与健康
工艺
文化与历史
娱乐
环境
食品与饮料
绿色未来
逆向工程
School Projects
科学
体育
技术
可穿戴设备
Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes
Karen

创建者

Karen

2. 七月 2026SE
1
0
0
0
0

Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes

The bee skep is the coiled-straw beehive that housed honeybees across Europe for roughly two thousand years, from antiquity into the 1800s, before wooden box hives replaced it. Using the same coiling technique as a straw basket, long rye straw is wound into a dome and stitched together with split cane. This blueprint builds a traditional skep by hand — from preparing the straw to the finished, weatherproofed hive ready to house a swarm.
中级
8

说明

1

Harvest and clean long rye straw

Cut long rye or wheat straw and strip off the seed heads and leaf sheaths, keeping the hollow stems long and unbroken for strong coils.

此步骤所需材料:

Rye StrawRye Straw1

所需工具:

KnifeKnife
2

Split and soak the binding cane

Split lengths of cane into thin flexible strips and soak them in water until pliable — these will sew the straw coils together.

此步骤所需材料:

Split CaneSplit Cane1
WaterWater3

所需工具:

KnifeKnife
3

Make the girth gauge

Form a small open ring about 2.5 cm across (the traditional 'girth', often a cow-horn tip). Straw fed through it keeps every coil the same thickness.

所需工具:

Skep Girth GaugeSkep Girth Gauge
4

Bind the crown

Take a small handful of straw, bend it into a tight knot to form the top knob of the skep, and lash it firmly with a strip of split cane.

此步骤所需材料:

Rye StrawRye Straw1
Split CaneSplit Cane1

所需工具:

AwlAwl
5

Feed straw into an even rope

Pass straw through the girth to form a continuous rope of even thickness, adding a few stems at a time so the bundle never thins as you work.

此步骤所需材料:

Rye StrawRye Straw1

所需工具:

Skep Girth GaugeSkep Girth Gauge
6

Sew the first coils to the crown

Coil the straw rope in a tight spiral around the crown. Push the awl through the coil below, pass split cane through, and pull each stitch snug about every 2 cm.

此步骤所需材料:

Split CaneSplit Cane1

所需工具:

AwlAwl
7

Spiral outward to start the dome

Continue spiralling outward from the crown, binding each new coil to the one below. The domed top of the hive begins to take shape.

此步骤所需材料:

Rye StrawRye Straw1
Split CaneSplit Cane1

所需工具:

AwlAwl
8

Build the domed wall downward

Work the spiral down and out to build the wall, keeping the girth on the rope to hold thickness and every binding stitch tight and evenly spaced.

此步骤所需材料:

Rye StrawRye Straw1
Split CaneSplit Cane1

所需工具:

AwlAwl
Skep Girth GaugeSkep Girth Gauge
9

Keep the courses even

Control how far each coil steps outward so the dome stays smooth and symmetrical. Steady, even courses make a strong, weathertight hive.

此步骤所需材料:

Rye StrawRye Straw1

所需工具:

AwlAwl
10

Widen to the finished base

As you near the bottom, let the coils reach the finished diameter of about 35–40 cm — the standard size for a colony of bees.

此步骤所需材料:

Rye StrawRye Straw1
Split CaneSplit Cane1

所需工具:

AwlAwl
11

Cut the flight entrance

At the lower edge, cut a small entrance notch in a coil so the bees can come and go once the skep is set open-side down.

所需工具:

KnifeKnife
12

Finish and lock the base coil

Complete the last coil at the base, taper off the straw rope, and lock the final binding stitches so the skep cannot unravel.

此步骤所需材料:

Split CaneSplit Cane1

所需工具:

AwlAwl
13

Trim the skep clean

Trim protruding straw ends and stray cane with the knife to leave a clean rim and an even outer surface.

所需工具:

KnifeKnife
14

Clom the outside for weatherproofing

Smear a thin coat of cow-dung-and-clay daub over the straw to shed rain and seal drafts, then let it dry — the traditional 'clomming'.

此步骤所需材料:

Cow DungCow Dung2 公斤
Ball ClayBall Clay1 公斤
15

Cure the finished skep

Cure the skep in a dry, airy place. Once fully dry it is ready to hive a swarm — set open-side down on a board or stand.

材料

6

所需工具

3

已连接蓝图材料

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

CC0 公共领域

此蓝图以 CC0 协议发布。你可以自由复制、修改、分发和使用此作品,无需征得许可。

通过购买蓝图中的产品支持创客,他们将获得 创客佣金 (由供应商设定),或创建此蓝图的新版本并将其作为连接包含在你自己的蓝图中以分享收入。

讨论

(0)

登录 加入讨论

加载评论中...