合作

艺术

美容与健康

工艺

文化与历史

娱乐

环境

食品与饮料

逆向工程

科学

体育

技术

可穿戴设备

Oil Storage Tank: a Riveted Steel Tank with Globe Roof (Bell, 1923)

H. S. Bell · Public domain in the US (published 1923)

创建者

Forge

4. 十一月 2026

Oil Storage Tank: a Riveted Steel Tank with Globe Roof (Bell, 1923)

An above-ground oil tank of riveted 'tank steel': a flat bottom, rings of plate lapped and riveted, angle irons at top and bottom, and a self-supporting globe roof. Every seam is caulked oil-tight and the tank is water-tested before painting. Variable: capacity. Bell's Fig. 158 is 1,000 barrels: 20 ft inside diameter, about 20 ft 3 in high, four rings of 1/4 in plate, sixteen 3/16 in roof plates rising 3 ft. Standard tanks run from 500 to 80,000 barrels (120 ft x 40 ft). Source: H. S. Bell, American Petroleum Refining (1923), pp. 286-306. Picture: Fig. 158 of the book.

专家

Unknown

说明

Choose the size and plates

Pick the capacity from the standard sizes (1,000 barrels: 20 ft diameter, 20 ft high). Take plate thickness from Bell's chart for the head and diameter, with a factor of safety of at least 2 1/2 for refinery tanks. Use at least 1/4 in for the shell; bottom 1/4 in on larger tanks, 3/16 in on smaller. Rings are 6 ft (72 in plates); about 7 ft is the limit.

所需工具：

未知尺寸

Prepare the ground

Level the ground in a circle 10 ft wider than the tank and remove all vegetable growth. Avoid a mix of cut and fill. In old yards filled with cinders, dig them out at least 8 in deep and replace with fine gravel, loam or sand. On poor soil, use piles.

此步骤所需材料：

砾石1 as needed

所需工具：

未知尺寸

Punch and scarf the plates

Punch the rivet holes. For 1/4 in plate with 5/8 in rivets, a single lap seam has holes 2 1/4 in apart and 1 1/8 in from the edge; keep the clear space between holes no more than 6 or 7 times the plate thickness, or the caulked edge springs. Scarf the corner of the middle plate where three plates meet: cold up to 1/4 in, hot above, drawn to an edge no thicker than 1/16 in.

所需工具：

冲床

大锤

Build the bottom on horses

Lay, rivet and caulk the bottom on trestles or horses about 30 in high. Rivet the bottom angle iron (Fig. 158: 3 x 3 x 5/16 in) with a 1/4 in bent-plate shoe behind each angle splice; caulk the shell leg past the shoe at least 12 in, or better bevel and caulk the angle all round. Assemble and drive the first ring while the bottom is still up. Test the bottom under 6 to 8 in of water. Coat its underside with ship-bottom or heavy asphalt paint.

此步骤所需材料：

低碳钢板1 bottom, first ring

低碳钢角钢1 bottom angle

钢铆钉1 个

未知材料1 asphalt paint

所需工具：

铆钉锤

扩孔冲子

水

宽排刷

Lower it and raise the shell

Raise the tank on jacks round the edge, clear out the horses and debris, and lower the bottom to grade. Rivet and caulk the remaining rings from scaffolds: floating scaffolds where water is at hand (water is pumped in as each ring is caulked tight, testing as you go), or brackets bolted through punched holes, later plugged with hot rivets. Where three plates meet, bolt them, heat cherry red with an oil-burning torch and lay the joint up with sledges before riveting. Fit the top angle (2 1/2 x 2 1/2 x 5/16 in) and a flanged steel manhole in the bottom ring.

此步骤所需材料：

低碳钢板1 rings

低碳钢角钢1 top angle

钢铆钉1 个

所需工具：

螺旋千斤顶

铆钉锤

扩孔冲子

火把

大锤

水

Fit the globe roof

For tanks up to 54 ft across, rivet on a self-supporting globe roof of segmental 3/16 in plates (Fig. 158: sixteen plates, 1/4 in centre plate, 3 ft rise); cold riveting is fine here. Make it gas-tight, with one vent at the apex covered by brass or monel wire cloth of at least 50 mesh.

此步骤所需材料：

低碳钢板1 roof

钢铆钉1 个

所需工具：

铆钉锤

Test and paint

Fill the tank with water to test it before painting; it shows the important leaks, though not always tightness for light oils. Wire-brush off mill scale and rust. Give shell and roof three coats: one of red lead ground in boiled linseed oil, then two of good grey graphite paint.

此步骤所需材料：