合作
艺术
美容与健康
工艺
文化与历史
娱乐
环境
食品与饮料
逆向工程
科学
体育
技术
可穿戴设备
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle.
Painted red inside and light green outside, lined in a lighter colour and black.
Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
中级
Unknown
说明
1
1
Make the hales
Make the hales
Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.
此步骤所需材料：
白蜡木板1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in所需工具：
手锯
手刨
双柄刮刨2
2
Frame with oak cross-pieces
Frame with oak cross-pieces
Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.
此步骤所需材料：
白橡木板1 个
木榫钉1 3/16 in pins所需工具：
夹背锯
榫眼凿
划线规
手摇曲柄钻与钻头
活动角度尺3
3
Fit the legs and stays
Fit the legs and stays
Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.
此步骤所需材料：
白橡木板1 legs 1 1/2 in square, stays
马车螺栓4 3 in所需工具：
手锯手摇曲柄钻与钻头
螺丝刀套装4
4
Bottom and sides
Bottom and sides
Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.
此步骤所需材料：
松木板1 1/2 in bottom, 5/8 in sides
油画颜料1 个所需工具：
手锯手刨
画笔套装5
5
Front board and ironwork
Front board and ironwork
Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.
此步骤所需材料：
松木板1 3/4 in front board
铁钉1 1 1/2 in cut nails
低碳钢扁钢1 7/8 in hoop iron
木螺钉1 3/4 in round-headed油画颜料1 个所需工具：
手锯
锤子螺丝刀套装画笔套装6
6
Make the wheel
Make the wheel
Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.
此步骤所需材料：
白蜡木板1 axle and felloes白橡木板1 spokes
铁棒1 3/8 in pins木榫钉4 1/4 in低碳钢扁钢1 3/4 x 1/8 in tyre所需工具：
木工车床双柄刮刨手摇曲柄钻与钻头锤子7
7
Hang the wheel and paint
Hang the wheel and paint
Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.
此步骤所需材料：
低碳钢扁钢2 3/4 x 1/8 in irons木螺钉1 个油画颜料1 个所需工具：
螺丝刀套装画笔套装材料
10- 1 axle and felloes占位符
- 1 spokes占位符
- 4 1/4 in占位符
- 4 3 in占位符
- 1 3/4 in front board占位符
- 3 个占位符
- 1 1 1/2 in cut nails占位符
- 2 3/4 x 1/8 in irons占位符
- 1 个占位符
- 1 3/8 in pins占位符
此蓝图制作
CC0 公共领域
此蓝图以 CC0 协议发布。你可以自由复制、修改、分发和使用此作品，无需征得许可。
通过购买蓝图中的产品支持创客，他们将获得 创客佣金 （由供应商设定），或创建此蓝图的新版本并将其作为连接包含在你自己的蓝图中以分享收入。