艺术
美容与健康
工艺
文化与历史
娱乐
环境
食品与饮料
逆向工程
科学
体育
技术
可穿戴设备
Whirl-Cone Splash-Guard Churn: A Whirl Feeds Air to a Cone, a Funnel Keeps the Cream In
Young set out to mingle "a large quantity of air" with the milk and to stop it "splashing out of the churn without interfering with the free action of the dasher."
John Young of West Galway, New York, received US 7,046, dated 22 January 1850, for an atmospheric churn: a geared spindle carrying a flat plate at its foot, an inverted conical vessel open at its top with wings on its rim, inverted channels on the plate leading out from the cone, and a spiral wing up the spindle. A loose inverted funnel on brackets near the top of the tub, with a small disk on the spindle partly closing its hole, returns whatever is thrown up.
This rung looks at the whirl, then prints the cone dasher, spiral wing, funnel and disk, fits them in a bucket, and makes butter.
中级
About 4 hours, plus printing
说明
1
1
The whirl
The whirl
正在加载 Jupyter 笔记本…
2
2
Air thrown out through channels before it
Air thrown out through channels before it
The embedded blueprint draws air down a hollow stem into radial channels. Young lets the cream's whirl bring the air down into an open cone instead.
3
3
Read US 7,046
Read US 7,046
"When the churn is supplied with milk and the dasher is rapidly turned by the application of power to the handle of the crank, the whole mass of milk is put in motion and a whirl is created around the spindle, through this whirl the air descends into the conical vessel D, from which it is discharged centrifugally through the channels g, g, and thus mingled with the milk."
4
4
Print the parts
Print the parts
Print the cone dasher in one piece (/uploads/blueprints/whirl-cone-splash-guard-churn-cone-dasher.stl): plate, open cone with rim wings, four inverted channels and a spider to the spindle. Print the spiral wing (/uploads/blueprints/whirl-cone-splash-guard-churn-spiral-wing.stl), the splash funnel (/uploads/blueprints/whirl-cone-splash-guard-churn-splash-funnel.stl), which needs a 200 mm bed, the disk (/uploads/blueprints/whirl-cone-splash-guard-churn-disk.stl) and the crank arm (/uploads/blueprints/whirl-cone-splash-guard-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
此步骤所需材料：
PETG线材1 个所需工具：
FDM 3D 打印机5
5
Spindle and dasher
Spindle and dasher
Slide the cone dasher, then the spiral wing, onto a 10 mm square hardwood spindle and glue them. Stand the spindle in a seat drilled in the centre of a food-grade bucket's floor.
此步骤所需材料：
硬木销钉1 个
木工胶1 个
20 升水桶1 个所需工具：
充电式电钻
钻头套装
手锯6
6
Funnel, disk and crank
Funnel, disk and crank
Screw three small wooden brackets inside the bucket 70 mm below the rim and set the funnel loosely on them, point down, the spindle through its hole. Glue the disk on the spindle just above the funnel's hole. Pass the spindle through a plywood lid and glue the crank arm and a dowel handle on top.
此步骤所需材料：
硬木块1 个
#8 × 1 英寸木螺钉1 个
胶合板1 个木工胶1 个所需工具：
手锯充电式电钻
螺丝刀套装7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the bucket cut away to show the plate with its open cone and inverted channels, the spiral wing, the loose funnel near the top and the disk on the spindle.
8
8
Spin and make butter
Spin and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 3 litres. Crank fast enough to raise a whirl round the spindle; time until the butter comes. Lift the funnel out before pouring off the buttermilk. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
此步骤所需材料：
鲜奶油3000 毫升
粗海盐1 个
水1 个所需工具：
留置式探针温度计
秒表
数字厨房秤
大号不锈钢搅拌盆9
9
No whirl, cream on the lid
No whirl, cream on the lid
Whirl-cone splash-guard churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**John Young** of West Galway, Fulton County, New York, received US 7,046, dated 22 January 1850. A pinion on the spindle geared into a wheel on the cover turned by the crank; the cone and channels came off the spindle by buttons or screws for cleaning; filled very full, the wings on the cone's rim kept its mouth open to the air. He claimed the combination of the inverted vessel H and the disk i on the dasher's stem to prevent the cream splashing out at the lid.
**Honest limits.** Our crank turns the spindle directly, without his wheel and pinion, so the whirl may be weaker; printed parts and a bucket stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
材料
10- 1 个占位符
- 1 个占位符
- 2 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 3000 毫升占位符
- 1 个占位符
- 1 个占位符
所需工具
9- 占位符
- 1 vendor sell this, none ship to you yet占位符
- 占位符
- 占位符
- 占位符
- 占位符
- 占位符
- 占位符
- 占位符
此蓝图制作
相关蓝图
这些蓝图共享知识——技术、材料或原理
CC0 公共领域
此蓝图以 CC0 协议发布。你可以自由复制、修改、分发和使用此作品，无需征得许可。
通过购买蓝图中的产品支持创客，他们将获得 创客佣金 （由供应商设定），或创建此蓝图的新版本并将其作为连接包含在你自己的蓝图中以分享收入。