KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

Erstellt von

Penny

14. Oktober 2026DK
23
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
Fortgeschritten
Two to three days

Anweisungen

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

Materialien für diesen Schritt:

Werkzeugstahl-FlachstabWerkzeugstahl-Flachstab1 Stück

Benötigte Werkzeuge:

MetallfeileMetallfeile
HandbohrerHandbohrer
Digitaler Messschieber 6 ZollDigitaler Messschieber 6 Zoll
SchmiedeesseSchmiedeesse
AbschreckbottichAbschreckbottich
SchutzbrilleSchutzbrille
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

Materialien für diesen Schritt:

HartholzleisteHartholzleiste2 Stück
Rundstahl (Baustahl)Rundstahl (Baustahl)0.3 m

Benötigte Werkzeuge:

MetallfeileMetallfeile
SchmiedeesseSchmiedeesse
AbschreckbottichAbschreckbottich
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

Materialien für diesen Schritt:

MessingblechMessingblech1 Stück
Gewachster LeinenzwirnGewachster Leinenzwirn3 m

Benötigte Werkzeuge:

BlechschereBlechschere
HandbohrerHandbohrer
MetallfeileMetallfeile
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

Benötigte Werkzeuge:

MetallfeileMetallfeile
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

Materialien für diesen Schritt:

MessingbarrenMessingbarren2 kg
HolzkohleHolzkohle1 as required
FormsandFormsand5 kg

Benötigte Werkzeuge:

SchmiedeesseSchmiedeesse
Schmelztiegel aus SchamotteSchmelztiegel aus Schamotte
TiegelzangeTiegelzange
Formkasten (Ober- und Unterkasten)Formkasten (Ober- und Unterkasten)
SchweißerhandschuheSchweißerhandschuhe
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

Materialien für diesen Schritt:

WasserWasser1 Liter

Benötigte Werkzeuge:

MesszylinderMesszylinder
MetallfeileMetallfeile
7

A binary set of weights

Jupyter-Notebook wird geladen …
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

Materialien

9

Benötigte Werkzeuge

12

CC0 Gemeinfrei

Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.

Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.

Diskussion

(0)

Anmelden um an der Diskussion teilzunehmen

Kommentare werden geladen...