Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
John R. Grundy · Public domain
Forge

Erstellt von

Forge

13. November 2026NO
0
0
0
0
0

One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)

John R. Grundy of Philadelphia received US 860,369, dated 16 July 1907, for a two-part collar held by a single screw, where earlier split collars needed two. The screw passes through one pair of ends, an overhang on one part lying over the other. At the opposite side a tongue on one part fits a recess in the other. Both of those ends reach round the shaft past the diameter under the screw. When the screw's point presses the shaft, they hook under it and cannot open. Each part goes onto the shaft from the side, so the shaft stays in its bearings. We cut the two parts from a turned brass ring with a piercing saw, from a full-size template. The patent gives no sizes; every size here is ours.
Erfahren
About 2 days

Anweisungen

1

Why the hooks hold

Jupyter-Notebook wird geladen …
2

Read US 860,369

"It is obvious that by using the single screw in place of a plurality of screws, as has hitherto been considered necessary, I am enabled to reduce the cost of the collar." "The parts of said collar are placed in position on the shaft by being moved toward it in radial planes."
3

Turn the ring

Grip 45 mm brass round bar in the 3-jaw chuck. Face it, turn it to 40 mm for 20 mm, centre-drill, drill through 15 mm and ream 16 mm. Part off 16 mm long and face the parted side.

Materialien für diesen Schritt:

Messing-RundstangeMessing-Rundstange1 Stück

Benötigte Werkzeuge:

MetalldrehmaschineMetalldrehmaschine
Dreibackenfutter für die DrehmaschineDreibackenfutter für die Drehmaschine
DrehmeißelDrehmeißel
Satz ZentrierbohrerSatz Zentrierbohrer
BohrersatzBohrersatz
ReibahleReibahle
AbstechstahlAbstechstahl
Digitaler Messschieber 6 ZollDigitaler Messschieber 6 Zoll
SchutzbrilleSchutzbrille
4

Print the cutting template

Full-size A4 template: the end view of the ring with the outlines of parts B and B', and the bottom of the ring seen from below with the tongue b' and cheeks a'. Print at 100 %; its 50 mm bar must measure 50 mm.
DesigndateiPDFCC0 - Free
Modell herunterladen
5

Cut the parts apart

Glue the end view on one end face of the ring, centred, and the strip on the outside at the bottom. Wax the blade. Top joint: hold the ring in soft jaws, face up, and saw with the blade along the axis: in from the outside 5 mm left of the line to 14 mm radius, round the 14 mm circle to the line, and down the line into the bore. Bottom joint: turn the ring over and saw with the blade across the wall, following the strip from one end face to the other: the cheeks a' 3 mm left of the line, the tongue b' 3 mm right of it. Go slowly at the corners; the two parts come apart.

Benötigte Werkzeuge:

TintenstrahldruckerTintenstrahldrucker
LeimLeim
SchraubstockSchraubstock
Schraubstock-SchutzbackenSchraubstock-Schutzbacken
JuweliersägeJuweliersäge
BienenwachsBienenwachs
6

Fit the joints and cut away the bores

File the saw marks off the joints until the tongue slides into its recess and the overhang lies on the other part, with the two parts round a 16 mm bar. File each part's bore out to 18 mm across over the 22 degrees next to the top joint on its own side, B' to the left of the line and B to the right, as the template shows. Try them on the bar: put B on from below right, then B' from below left, sliding it up under the overhang and the tongue into its recess. File until each goes on without forcing.

Benötigte Werkzeuge:

Rundstahl aus BaustahlRundstahl aus Baustahl
SchraubstockSchraubstock
Schraubstock-SchutzbackenSchraubstock-Schutzbacken
FeilensatzFeilensatz
NadelfeilensatzNadelfeilensatz
Digitaler Messschieber 6 ZollDigitaler Messschieber 6 Zoll
7

Drill and tap for the screw

With both parts on the bar, the overhang lying on B', clamp the bar in the machine vice so the dashed screw line on the template stands upright. Drill 4.2 mm through the overhang and through B' into the bore, and tap M5 through both with cutting oil. Take the parts off and deburr the bore.

Materialien für diesen Schritt:

SchneidölSchneidöl1 Stück

Benötigte Werkzeuge:

Rundstahl aus BaustahlRundstahl aus Baustahl
StandbohrmaschineStandbohrmaschine
MaschinenschraubstockMaschinenschraubstock
BohrersatzBohrersatz
GewindeschneidsatzGewindeschneidsatz
WindeisenWindeisen
EntgraterEntgrater
8

The collar in 3D

FreeCAD model, our sizes: parts B and B' on a 16 mm shaft, the overhang b and the M5 screw at the top, the tongue b' between the cheeks a' at the bottom, and the bores cut away beside the top joint.
DesigndateiSTLCC0 - Free
Modell herunterladen
9

Fit it on the shaft

Run an M5 x 12 cup point set screw into the overhang until it just shows. Put B onto the shaft from the side where the collar is wanted, then B' from the other side, its top under the overhang and its tongue into the recess. Tighten the screw with the hex key: it pushes on the shaft and draws both bottom ends down against it. Try to slide and turn the collar; it must not move.

Materialien für diesen Schritt:

Madenschraube mit RingschneideMadenschraube mit Ringschneide1 Stück

Benötigte Werkzeuge:

Innensechskant-SchlüsselsatzInnensechskant-Schlüsselsatz
10

Troubleshooting

Grundy collar troubleshooting.

Flow

Loading...
11

History and honest limits

**John R. Grundy** of Philadelphia, US 860,369, dated 16 July 1907, filed 28 January 1907. He claimed "a shaft collar made in two parts, and means for holding the parts together comprising a single screw passing through two adjacent ends of said two parts, the other ends of said parts being formed to co-act with the shaft to prevent their separation". His screw end also has a second projection b2 in a recess, holding the parts in line along the shaft; ours leaves it out, as the screw through both parts does that. His screw has a hex head; ours is a socket set screw. He gives no material; ours is brass, which a piercing saw cuts well. The patent gives no sizes; every size here is ours.

Materialien

3

Benötigte Werkzeuge

24

Designdateien

2

Dieser Bauplan stellt her

Thumbnail
Platzhalter

Shaft Collar

Free

5
0
1

Verwandte Blueprints

Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien

Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)

Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)

von ForgeNO

Metallbearbeitung

0
0
0
0
0
0
Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)

Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)

von ForgeNO

Metallbearbeitung

0
0
0
0
0
0

CC0 Gemeinfrei

Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.

Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.

Diskussion

(0)

Anmelden um an der Diskussion teilzunehmen

Kommentare werden geladen...