Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap
L. Lake (USPTO drawing) · Public domain
Martin

Erstellt von

Martin

9. November 2026NO
2
0
0
0
0

Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap

Lorenzo Lake of Middlebury, Pennsylvania, received US 24,845, dated 19 July 1859, for an upright dash churn worked by gearing so that a child could churn even a very large churn. A handle turns a large wheel driving a wheel half its size on a crank shaft with a balance wheel; the crank's pitman works the staff up and down through a guide. The staff carries two dashers of boards with V-shaped slots in their ends, set so the points of one lie over the gaps of the other, cutting the cream as it escapes going down and up and dashing it against the sides. This rung builds it with printed gears over a 20-litre bucket.
Fortgeschritten
About 2 days, plus printing

Anweisungen

1

Strokes per turn of the handle

Jupyter-Notebook wird geladen …
2

A crank and pitman working the staff, before it

Dorsey's pitman also turned the staff. Lake's only lifts it, through gearing and a balance wheel for speed.
3

Read US 24,845

"... these dashers are so placed upon the staff that the sharpened ends of the boards thus cut, will cover the spaces left between the boards in the dasher immediately above or below—so that when operated in the churn the cream will be more thoroughly cut and the globules will be more easily and speedily broken."
4

Print the wheel E

The 40-tooth wheel for the handle's shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
DesigndateiSTLCC0 - Free
Modell herunterladen
5

Print the wheel F

The 20-tooth wheel for the crank shaft. PETG, 0.2 mm layers, 50 % infill, 5 walls.
DesigndateiSTLCC0 - Free
Modell herunterladen
6

Platform, upright and frame

Screw a pine platform C 500 x 550 mm. Stand a 70 mm upright C' 990 mm tall at its back, braced. Screw a hardwood beam 130 x 255 x 40 mm out from the upright's top toward the front, and hang three hardwood blocks from it, each bored 20.5 mm 900 mm above the floor: two either side of the crank, 90 mm apart, for shaft G, and one 90 mm to the side for wheel E's shaft. Screw a hardwood guide arm I from the upright to over the bucket 430 mm up, with a 26 mm square hole.

Materialien für diesen Schritt:

KiefernbrettKiefernbrett2 Stück
Nadelholz 70x70 mmNadelholz 70x70 mm2 Stück
HartholzbrettHartholzbrett2 Stück
Holzschraube Nr. 10 x 3"Holzschraube Nr. 10 x 3"20 Stück
HolzleimHolzleim1 Stück

Benötigte Werkzeuge:

HandsägeHandsäge
AkkubohrschrauberAkkubohrschrauber
Flachfräsbohrer-SatzFlachfräsbohrer-Satz
StechbeitelStechbeitel
WasserwaageWasserwaage
Bandmaß (Rollmeter)Bandmaß (Rollmeter)
7

Crank shaft G, wheels and handle

Make the crank from two hardwood webs 30 x 10 mm, a 12 mm stainless pin 50 mm off the axis between them, and two 20 mm steel stubs, one each side, run through the hanging blocks. Fix wheel F on the rear stub and a plywood balance wheel B 300 mm across, with spokes, on the front stub. Run a 20 mm steel shaft through the third block with wheel E meshing with F, and a hardwood handle M 57 mm long with a dowel grip on its end.

Materialien für diesen Schritt:

HartholzbrettHartholzbrett1 Stück
EdelstahlstabEdelstahlstab1 Stück
Stahl-StangenmaterialStahl-Stangenmaterial2 Stück
PETG-FilamentPETG-Filament1 Stück
SperrholzplatteSperrholzplatte1 Stück
HartholzdübelHartholzdübel1 Stück
HolzleimHolzleim1 Stück
Sechskantschrauben-SortimentSechskantschrauben-Sortiment4 Stück
Sicherungsmutter mit KunststoffeinsatzSicherungsmutter mit Kunststoffeinsatz4 Stück

Benötigte Werkzeuge:

FDM-3D-DruckerFDM-3D-Drucker
StichsägeStichsäge
Bügelsäge (Metallsäge)Bügelsäge (Metallsäge)
AkkubohrschrauberAkkubohrschrauber
BohrersatzBohrersatz
Feilen (Handfeile)Feilen (Handfeile)
RollgabelschlüsselRollgabelschlüssel
8

Staff, dashers and pitman

Cut two plywood dashers L, each a 16-point star 250 mm across with its notches 20 mm deep, and a 25 mm square hole in the middle. Glue them on a 25 mm square hardwood staff D 150 mm apart, the upper turned half a point from the lower. Cut a hardwood pitman H 300 mm between centres with a fork at its foot; fit a hardwood thimble J on the staff's top and push an 8 mm stainless rod a through the fork, thimble and staff. Put the staff through the guide and the bucket's lid and set the lower dasher 25 mm off the floor at the bottom of the stroke.

Materialien für diesen Schritt:

SperrholzplatteSperrholzplatte1 Stück
HartholzbrettHartholzbrett2 Stück
HolzleimHolzleim1 Stück
EdelstahlstabEdelstahlstab1 Stück
UnterlegscheibeUnterlegscheibe2 Stück
20-Liter-Eimer20-Liter-Eimer1 Stück

Benötigte Werkzeuge:

StichsägeStichsäge
HandsägeHandsäge
StechbeitelStechbeitel
AkkubohrschrauberAkkubohrschrauber
BohrersatzBohrersatz
SchleifpapierSchleifpapier
9

The build in 3D

FreeCAD model of this build, half the bucket cut away: the platform and upright, the beam with its hanging blocks, the split crank shaft with balance wheel and wheel F, wheel E and handle M, the forked pitman and thimble, the staff through its guide, and the two star dashers. It was checked at eight crank angles.
DesigndateiBLENDCC0 - Free
Modell herunterladen
10

Churn

Pour about 10 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the lid on round the staff. Turn the handle steadily and time it. When the butter comes, pull pin a, lift the staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materialien für diesen Schritt:

SchlagsahneSchlagsahne10 l
Grobes MeersalzGrobes Meersalz1 Stück
WasserWasser1 Stück

Benötigte Werkzeuge:

Einsteck-FühlerthermometerEinsteck-Fühlerthermometer
StoppuhrStoppuhr
Digitale KüchenwaageDigitale Küchenwaage
Große Rührschüssel aus EdelstahlGroße Rührschüssel aus Edelstahl
11

Troubleshooting

Star-dasher churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Lorenzo Lake** of Middlebury, Tioga County, Pennsylvania, assignor to himself and William Patton of Towanda, US 24,845, 19 July 1859, "Churn". He claimed the dasher L worked by the devices described, not the gearing as such. His only proportion is wheel F about half wheel E. His dashers are boards with V-slotted ends; ours are plywood stars cut to the same pattern. Every size is ours.

Materialien

17

Benötigte Werkzeuge

17

Designdateien

3

Dieser Bauplan stellt her

Thumbnail
Platzhalter

Butter

Free

198
0
1
Thumbnail
Platzhalter

Buttermilch

Free

72
0

Verwandte Blueprints

Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien

Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once

Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once

von MartinNO

Holzbearbeitung

2
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation

Churning Butter from Cream — The 5,000-Year-Old Fat Separation

von TheChefDK

HANDWERK

60
0
0
0
0
0

CC0 Gemeinfrei

Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.

Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.

Diskussion

(0)

Anmelden um an der Diskussion teilzunehmen

Kommentare werden geladen...