KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Carving a Wooden Clog — The All-Wood Sabot from a Single Green Block
Across rural Europe the wooden clog — the French sabot, the Dutch klomp — kept feet warm and dry for centuries. Each shoe is carved from a single block of green hardwood: the outside shaped like a foot, the inside hollowed out to receive it. Green (unseasoned) alder, willow or beech is used because it carves easily and splits little, then hardens as it dries. This blueprint carves one clog from froe-split billet to finished shoe, then repeats for the matching pair, using only edge tools.
Fortgeschritten
6
Anweisungen
1
1
Split a clean billet
Split a clean billet
Split a straight-grained block of green alder, willow or beech to a little larger than the foot, using the froe driven with a wooden mallet. Choose a length free of knots so the wood carves cleanly.
Materialien für diesen Schritt:
Hartholzblock1 StückBenötigte Werkzeuge:
Spaltmesser (Froe)
Holzhammer (Klüpfel)2
2
Rough out the foot profile
Rough out the foot profile
With the hatchet, chop the billet down to the rough shape of a foot seen from the side — a flat sole, an upturned toe, and a squared heel. Leave the block oversize everywhere for now.
Benötigte Werkzeuge:
Beil3
3
Mark the sole and top outlines
Mark the sole and top outlines
Stand the block on the wearer's foot or a pattern and mark the outline of the sole and the top opening with the point of the carving knife, so you have clear lines to carve to.
Benötigte Werkzeuge:
Sloyd-Schnitzmesser4
4
Shape the outside with the drawknife
Shape the outside with the drawknife
Clamp the block and draw the drawknife toward you to shape the rounded outside of the clog — the swell of the toe, the waist at the instep, and the flat of the sole. Work down to the marked lines.
Benötigte Werkzeuge:
Zugmesser5
5
Refine the curves with a spokeshave
Refine the curves with a spokeshave
Smooth the toe curve, the sides and the instep with the spokeshave, fairing the outside into an even foot shape ready to hollow.
Benötigte Werkzeuge:
Schweifhobel6
6
Bore out the mouth
Bore out the mouth
Bore down into the top opening with the hand auger to remove the bulk of the inside waste quickly, stopping short of the sole so you do not bore through.
Benötigte Werkzeuge:
Handbohrer (Nabenbohrer)7
7
Hollow the foot cavity
Hollow the foot cavity
Hollow the inside to the shape of a foot with the hook knife and gouge, driven by the mallet where needed. Follow the curve of the sole and open out under the instep, leaving even walls.
Benötigte Werkzeuge:
Hohlmesser (zum Löffelschnitzen)
HohlbeitelHolzhammer (Klüpfel)8
8
Fit the cavity to the foot
Fit the cavity to the foot
Test the hollow against the foot it must fit: the sole should sit flat, the toes have room, and the walls be thin enough to be light but thick enough to be strong. Pare away any tight spots.
Benötigte Werkzeuge:
Hohlmesser (zum Löffelschnitzen)9
9
Cut the instep throat
Cut the instep throat
Shape the opening at the top of the foot — the 'throat' — with the gouge and carving knife so the foot slides in and the clog grips the instep without pinching.
Benötigte Werkzeuge:
HohlbeitelSloyd-Schnitzmesser10
10
Smooth inside and out
Smooth inside and out
Pare every surface smooth, inside and out, with the carving knife and spokeshave, removing tool ridges so nothing chafes the foot and the outside is clean.
Benötigte Werkzeuge:
Sloyd-SchnitzmesserSchweifhobel11
11
Carve the matching clog
Carve the matching clog
Repeat every step to carve the second clog as a mirror image of the first, so the pair matches in length, depth and shape — one left, one right.
Materialien für diesen Schritt:
Hartholzblock1 StückBenötigte Werkzeuge:
BeilZugmesserHohlmesser (zum Löffelschnitzen)12
12
Dry the pair slowly
Dry the pair slowly
Set the finished green-wood clogs to dry slowly in a cool, airy place away from direct heat. As the wood seasons it hardens and the clogs become light and durable — drying too fast would crack them.
Materialien
1- 1 StückPlatzhalter
Benötigte Werkzeuge
9- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Materialien verbundener Blueprints
Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Using a Drawknife — Shaping Riven Timber by Drawing a Blade Toward You
von Woody
Holzbearbeitung
48
0
0
0
1
0
Building a Shave Horse — The Foot-Operated Clamping Bench for Green Woodworking
von Woody
Holzbearbeitung
55
0
0
0
1
0
Building a Pole Lathe for Green Wood Turning — Spring-Pole Reciprocating Lathe
von Woody
Holzbearbeitung
194
1
0
0
2
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.