Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Rip Saw: a Hand Saw Filed with Upright Teeth and Little Set (Cassell's Cyclopaedia, 1904)
A rip saw cuts along the grain, so its teeth work like a row of small chisels, not like the knife points of a cross-cut saw. Cassell's Cyclopaedia of Mechanics (1904) says how to file one: the fronts of the teeth perfectly upright, the faces given a transverse bevel of only 3 to 5 degrees (the file held at 85 and 95 degrees), and only a little set, less than a cross-cut saw needs.
It gives no tooth size, back angle or amount of set; those are unknown here.
Source: P. N. Hasluck (ed.), Cassell's Cyclopaedia of Mechanics vol. V (1904), p. 73, Setting Saw Teeth. Picture: our diagram.
Fortgeschritten
An hour
Anweisungen
1
1
Read Cassell's
Read Cassell's
"The teeth in a rip saw should be so filed that their fronts will be perfectly upright. A transverse bevel of from 3° to 5° should be given to the faces of the teeth."
2
2
Clamp the saw
Clamp the saw
Clamp the hand saw in the vice with its teeth just above the jaws, so the blade cannot chatter under the file.
Materialien für diesen Schritt:
Tischlersäge1 hand sawBenötigte Werkzeuge:
Schraubstock3
3
File the teeth upright
File the teeth upright
File each tooth so its front stands perfectly upright to the line of the teeth. Hold the file at 85° to the blade for one side and 95° for the other, to give the faces a transverse bevel of about 5°; 3° is the least. File alternate teeth from one side, then turn the saw and file the others. Tooth size and the slope of the backs are not given (unknown).
Benötigte Werkzeuge:
Sägefeile
Unbekannte Maße4
4
Set lightly and evenly
Set lightly and evenly
Set the teeth alternately left and right with the saw set, the same amount on each side. A properly ground ripping saw needs only a little set, less than a cross-cut saw; how much depends on the timber, the thickness of the blade and how it is ground (not given, unknown).
Benötigte Werkzeuge:
SägeschränkzangeUnbekannte Maße5
5
History and honest limits
History and honest limits
On the same page Cassell's gives the other hand saws: a cross-cut saw's fronts recline about 10° and need a keener edge, a tenon saw is filed much like a hand saw with less bevel, and a panel saw, used both ripping and cross-cutting, like a mitre saw.
Tooth size, back angle and amount of set are not given; the saw is a hand saw refiled for ripping.
Materialien
1- 1 hand sawPlatzhalter
Benötigte Werkzeuge
4- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Dieser Bauplan stellt her
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.