KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Youblob · CC0
55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)
The open-top 55-gallon (208-litre) steel drum, built to the rule US railways and shippers used for single-trip removable-head drums: welded low-carbon steel body, three rolled hoops, a crowned bottom, and a lid clamped by a bolted ring over a gasket.
Source: ICC Specification 17H, 49 CFR 78.118, Federal Register, 29 December 1964. The spec does not say how the bottom is joined. The litre figure, the gasket rubber and the machines are ours. Picture drawn by Youblob.
Erfahren
Production line
Anweisungen
1
1
Cut low-carbon steel sheets
Cut low-carbon steel sheets
Use low-carbon steel for body and heads. For a 55-gallon drum: body 18 gauge, bottom head 18 gauge, removable head 14 gauge (16 gauge if the cover has one or more corrugations near its edge). 18 gauge is 0.0478 in nominal and at least 0.0428 in; 14 gauge 0.0747 in and at least 0.0677 in, measured at least 3/8 in from an edge.
Materialien für diesen Schritt:
Baustahlblech1 body, bottom and lid sheetsBenötigte Werkzeuge:
Kraftblechschere
Mikrometer2
2
Roll and weld the body
Roll and weld the body
Roll the body sheet into a cylinder and weld the seam. The body seam must be welded.
Benötigte Werkzeuge:
Blechbiegewalzen
Rohrnaht-Schweißanlage3
3
Roll in three hoops
Roll in three hoops
Roll or swage three hoops into the body, one of them near the top curl.
Benötigte Werkzeuge:
Sickenwalzen4
4
Press crowned heads
Press crowned heads
Press the bottom head crowned (convex) by at least 3/8 in, not standing out beyond the level of the chime, and fit it to the body. The spec does not say how the bottom is joined.
Benötigte Werkzeuge:
Stanzpresse5
5
Make the bolted ring and gasket
Make the bolted ring and gasket
Make the closing ring from 12-gauge steel with drop-forged lugs, one of them threaded, and a 5/8 in bolt and nut (for drums over 30 gallons). Fit a gasket under the lid: gaskets are required.
Materialien für diesen Schritt:
Baustahlblech1 12-gauge strip for the ring
Rundstahl aus Baustahl1 for the lugs
Sechskantschrauben-Sortiment1 5/8 in bolt
Sechskantmutter1 5/8 in
Gummiplatte1 gasketBenötigte Werkzeuge:
Blechbiegewalzen
Fallhammer mit Schmiedegesenken
Bastelmesser6
6
Check capacity and mark
Check capacity and mark
The drum must hold at least 4 % more than its marked 55 gallons, and no more than 5 % more (or 4 % plus 1 quart, whichever is greater). Emboss the marks: ICC-17H, STC (single-trip container), the maker, and the gauges, capacity and year.
Benötigte Werkzeuge:
Stanzpresse7
7
Leak-test every drum
Leak-test every drum
Test each drum by air pressure inside of at least 7 psi with its seams under water or covered with soapsuds or heavy oil. Reject leakers, or repair them the way they were made and test again.
Materialien für diesen Schritt:
Wasser1 as requiredBenötigte Werkzeuge:
Luftkompressor
Manometer8
8
Type tests every four months
Type tests every four months
On drums taken at random and closed as for use: drop one filled with water to 98 % from 4 ft onto concrete so it lands diagonally on the chime, and hold another at 15 psi water pressure for 5 minutes. None may leak.
Materialien für diesen Schritt:
Wasser1 as requiredBenötigte Werkzeuge:
ManometerMaterialien
6- 1 12-gauge strip for the ringPlatzhalter
- 1 for the lugsPlatzhalter
- 1 5/8 in boltPlatzhalter
- 1 5/8 inPlatzhalter
- 1 gasketPlatzhalter
- 2 as requiredPlatzhalter
Benötigte Werkzeuge
10- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
Dieser Bauplan stellt her
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.