Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Three-Piece Airlock, 3D Printed in PETG
3DBonanza

Erstellt von

3DBonanza

18. November 2026US
1
0
0
1
0

Three-Piece Airlock, 3D Printed in PETG

An airlock lets the carbon dioxide of a fermenting beer, wine or cider out through a little water, and keeps outside air out. This one has the four parts of the "standard type device" named in L. P. Beadle's 1980 US patent 4,218,964: a cap, a tapered stem, a housing two-thirds full of water, and a cone member. It prints in three pieces in PETG. All sizes are ours, and we have not printed or tested it yet: the leak test below comes first.
Anfänger
About 5 hours, mostly printing

Anweisungen

1

Seal pressure and water back-flow

Jupyter-Notebook wird geladen …
2

Read US 4,218,964

"Housing 27 is filled two-thirds full with water, cone 28 is inserted and cap 25 is secured ... excess gas escapes by bubbling through the water in lock 14 so as to protect the beer ingredients within container 11 from contact with outside air." The picture is our section: gas goes up the stem, under the cone member's rim and out of the cap.
Schritt 2 - Image 1
3

Print the housing and stem

Stand it on the stem's tip with a 10 mm brim; the 45 degree cone under the floor needs no supports. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
DesigndateiSTLCC0 - Free

Materialien für diesen Schritt:

PETG-FilamentPETG-Filament15 g

Benötigte Werkzeuge:

FDM-3D-DruckerFDM-3D-Drucker
Düsensatz für 3-D-DruckerDüsensatz für 3-D-Drucker
4

Print the cone member

Print it upside down, closed end on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
DesigndateiSTLCC0 - Free

Materialien für diesen Schritt:

PETG-FilamentPETG-Filament3 g

Benötigte Werkzeuge:

FDM-3D-DruckerFDM-3D-Drucker
Düsensatz für 3-D-DruckerDüsensatz für 3-D-Drucker
5

Print the cap

Print it upside down, top on the bed. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 4 walls so no water finds a path between the layers.
DesigndateiSTLCC0 - Free

Materialien für diesen Schritt:

PETG-FilamentPETG-Filament3 g

Benötigte Werkzeuge:

FDM-3D-DruckerFDM-3D-Drucker
Düsensatz für 3-D-DruckerDüsensatz für 3-D-Drucker
6

Clean the parts

Take off the brim. Turn a 5 mm drill bit through the stem by hand to clear any strings. Check the stem: 10.0 mm at the top, 8.5 mm at the tip.

Benötigte Werkzeuge:

BohrersatzBohrersatz
Digitaler Messschieber 6 ZollDigitaler Messschieber 6 Zoll
7

Leak test

Fill the housing with water to the groove. Stand it in a dry glass for an hour. Any drop on the outside or in the glass means a leak: print again.

Benötigte Werkzeuge:

WasserWasser
8

Sanitise

Soak all three parts in no-rinse sanitiser mixed as its label says. Do not boil them: PETG softens at about 80 °C.

Benötigte Werkzeuge:

DesinfektionsmittelDesinfektionsmittel
WasserWasser
9

Assemble and fill

Drop the cone member over the riser tube. Fill the housing to the groove with sanitiser solution, not plain water. Push the cap on.

Benötigte Werkzeuge:

DesinfektionsmittelDesinfektionsmittel
WasserWasser
10

Fit it to the fermenter

Push the stem into the bored stopper or the lid's hole. The stem gets thinner towards the tip, so it wedges tight, as in Beadle's patent. Gas must bubble through the water, never round the stem.

Benötigte Werkzeuge:

GummistopfenGummistopfen
11

Troubleshooting

Airlock problems and fixes.

Flow

Loading...
12

History and honest limits

**Leigh P. Beadle**, US 4,218,964, "Lid construction for fermentation container", filed 21 May 1979, issued 26 August 1980, assigned to Specialty Products International Ltd. His invention was the lid; he calls the airlock "a standard type device" and names its parts: cap 25, tapered stem 26, housing 27 and cone member 28. He gives no sizes and no material for the lock. Ours: every size, the riser tube, the three ribs, the vent holes, the posts that stop the cone member lifting more than 3.4 mm, and PETG. Checked in CAD for fit; not yet printed or brewed with by us.

Materialien

1

Benötigte Werkzeuge

7

Designdateien

3

Dieser Bauplan stellt her

CC0 Gemeinfrei

Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.

Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.

Diskussion

(0)

Anmelden um an der Diskussion teilzunehmen

Kommentare werden geladen...