Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES

Woven Collection Basket: the Oval Willow Linen Basket (Hasluck, 1903)
A large woven willow basket with a handle at each end, for carrying linen or gathered goods: the basket-maker's oval linen basket, with a crowned oval bottom woven on a tied 'slarth', stakes pushed in round it, randed sides 7 in deep at the ends and 2 1/2 in higher at the sides, a wale and a plaited border. About 22 in long.
Variable: randed (16 pairs of stakes) or slewed (15 1/2 pairs).
Source: Paul N. Hasluck, Basket Work of All Kinds (1903), pp. 55-63. Picture: Fig. 58 of the book.
Erfahren
Unknown
Anweisungen
1
1
Cut the bottom sticks
Cut the bottom sticks
For a 14 in bottom cut seven sticks about 12 in long, shaving a little off along the middle, and an 8 in piece of rod to divide the tie-rods. Take eight tie-rods. Up to 14 in use three lays of sticks; larger bottoms need four and thicker sticks.
Materialien für diesen Schritt:
Dickere Weidenruten7 12 in
Weidenrute8 tie-rodsBenötigte Werkzeuge:
Einhand-Gartenschere2
2
Tie the slarth
Tie the slarth
On the board, put four tie-rods' butts under the right foot. About 5 in from the ends lay two sticks between A and C and between B and D, then three sticks about 2 3/4 in further on, then the last two, so the three lays fill a 7 in space; slip the 8 in piece under the three middle sticks (Fig. 57). Work the other four rods between the sticks with butts the opposite way (Fig. 58), passing each tightly over and under, tapping them close with the iron and pulling up the sticks each time to crown the bottom. Lay the slarth about half the finished length.
Benötigte Werkzeuge:
Flaches Holzbrett
Hammer3
3
Open the sticks and pair the bottom
Open the sticks and pair the bottom
Work the tie-rod tops round in pairs, opening the sticks into separate groups. Point a handful of rods at the butt, wet the points, and pair them in, thinnest and shortest first, one rod under and over the other, starting at either side, until the bottom is 14 in long. Finish the last pair in and out of the pairing, pick off the ends and cut off the stick ends with the shears.
Materialien für diesen Schritt:
Weidenrute1 pairing rodsBenötigte Werkzeuge:
Einhand-Gartenschere
Schere (groß)
Wasser4
4
Stake up and upset
Stake up and upset
Cut stakes as for a round basket: 16 pairs for a randed basket, 15 1/2 for a slewed one. Push them in, a pair beside each stick, turn the bottom over and press it down, prick up each stake and gather them in a large hoop; drive them in close. Upset with four rods, each in front of three stakes and behind the fourth, and add a second round.
Materialien für diesen Schritt:
Weidenstecklinge32 16 pairs
Weidenrute1 upsettingBenötigte Werkzeuge:
Durchziehnadel
Einhand-Gartenschere
Hammer5
5
Rand the sides and wale
Rand the sides and wale
Free the end stakes from the hoop: the top needs a good 8 in spring from end to end. Work a few short pieces at each side first, ends left outside so the inside stays smooth, then rand round to the right until the ends are 7 in high and the basket measures 22 in end to end. Raise the sides about 2 1/2 in higher than the ends. Work a wale of three rods (inside two stakes, outside one) or four (inside two, outside two).
Materialien für diesen Schritt:
Weidenrute1 randing, waleBenötigte Werkzeuge:
Hammer
Wasser6
6
Border and handles
Border and handles
Begin the border by laying down five rods, each worked in front of four stakes and behind two; finish by cramming and trim with the picking knife. For each end handle push in two rods beside stakes three or four apart; bend one into a bow under the border, twist the other rope-fashion and lap it over the bow three times each way, then lap the bow rod's own top across it.
Materialien für diesen Schritt:
Weidenrute9 5 border rods, 4 handle rodsBenötigte Werkzeuge:
Durchziehnadel
Einhand-GartenschereMaterialien
3- 7 12 inPlatzhalter
- 9 5 border rods, 4 handle rodsPlatzhalter
- 32 16 pairsPlatzhalter
Dieser Bauplan stellt her
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.
