Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)
Forge

Creado por

Forge

4. noviembre 2026NO
14
0
0
0
0

Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)

A shop brazing and tempering torch: a wall-hung pipe tank of gasoline or kerosene pumped up with a bicycle pump, feeding a 1/8 in pipe whose end is coiled round a short 1 in pipe; the flame heats the coil, the oil turns to gas, and it blasts out through a pinhole cap. Two burners on a tee give a bigger heat. Source: Popular Mechanics Shop Notes for 1909, pp. 861-862. Picture: the article's drawing.
Intermedio
Unknown

Instrucciones

1

Make the tank

Cap both ends of a 2 in pipe 20 in long. Drill three holes in the top cap: one for the rubber tube from a bicycle pump, one for a steam gauge, and one with a screw plug for filling with fuel oil.

Materiales para este paso:

Tubo de acero (de pared gruesa, con roscas)Tubo de acero (de pared gruesa, con roscas)1 2 in x 20 in
Accesorio roscado para tuberíaAccesorio roscado para tubería3 two caps, plug
ManómetroManómetro1 pieza
Tubo de gomaTubo de goma1 pieza

Herramientas necesarias:

Taladro de manoTaladro de mano
Juego de machos y terrajasJuego de machos y terrajas
Llave de tuboLlave de tubo
Bomba de pie para bicicletaBomba de pie para bicicleta
2

Coil the burner

Drill the bottom cap and connect a 1/8 in pipe D, any length, with a globe valve in it to set and shut off the oil. Fill the last 10 in of the pipe with lead, coil it round a 1 in pipe F 6 in long, and turn the end out to take two elbows and a short nipple; then melt the lead out. Drill a small hole in the centre of a 1/8 in cap and fit it on the end (E) so the hole lines up with the centre of pipe F.

Materiales para este paso:

Tubo de acero (de pared gruesa, con roscas)Tubo de acero (de pared gruesa, con roscas)1 1/8 in, and 1 in x 6 in
Accesorio roscado para tuberíaAccesorio roscado para tubería4 two elbows, nipple, 1/8 in cap
Válvula de globoVálvula de globo1 pieza

Herramientas necesarias:

PlomoPlomo
Espumadera perforadaEspumadera perforada
FraguaFragua
Taladro de manoTaladro de mano
Llave de tuboLlave de tubo
3

Start the burner

Hang a little cup holding three or four teaspoonfuls of oil just below the coil and light it to heat the coil; then pump up the tank and open the globe valve. For more heat connect two burners on a tee so their blasts meet.

Herramientas necesarias:

QuerosenoQueroseno
Bomba de pie para bicicletaBomba de pie para bicicleta

Materiales

5

Herramientas requeridas

8

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...