Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
PlanosARTESANÍA
ARTESANÍA
2105 blueprints disponibles • 11 subcategorías
Explorar Subcategorías
Planos (2105)
Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Threaded-Stud Rubber-Head Hammer: Heads Screw Onto the Body's Own Studs and Lock the Handle's Nail In (Dicks, 1951)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Laminated Rubber Mallet: A Rubber-and-Canvas Head Locked on a Flared Handle by an Internal Rib (Whisler, 1924)
por Forge
Carpintería
0
0
0
0
0
0
Laminate Bevel Trimmer: Two Pads at Right Angles Hold a Small Router at 45 Degrees on a Corner (Roche, 1971)
por Forge
Carpintería
0
0
0
0
0
0
Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)
por Forge
Carpintería
0
0
0
0
0
0
Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)
por Forge
Industry 3.0 — Assembly Line & Mass Production (1913)
0
0
0
0
0
0
Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)
por Forge
Carpintería
0
0
0
0
0
0
Screw-Depth Portable Router: The Motor's Threaded Casing Screws Into a Split Base, One Turn per Sixteenth (Carter, 1924)
por Forge
Carpintería
0
0
0
0
0
0
Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)
por Forge
Carpintería
0
0
0
0
0
0
Sliding-Table Saw That Switches Itself: A Hand Saw Under a Table on Balls, Turned On and Off by the Stroke (Tracy, 1941)
por Forge
Carpintería
0
0
0
0
0
0
Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
por Forge
Carpintería
0
0
0
0
0
0
Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)
por Forge
Carpintería
0
0
0
0
0
0
Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
por Forge
Carpintería
0
0
0
0
0
0
Long-Pilot High-Speed Wood Bits: A Flat Plate and a Long Square-Edged Pilot, No Screw Feed (Smith, 1951)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Angled-Side Spade Bits: Each Wing Bent Forwards Along a Diagonal Line, the Way the Bit Turns (Vasudeva, 2005)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Fluted-Shoulder Spade Bits With Spurs: Flutes Along the Shoulders, Stopped by Corner Spurs (Williams & Thackston, 1987)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Diamond-Point Spade Bits: A Thinned, Wide-Angled Point Does More of the Cutting (Southall, 1975)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Fluted-Point Spade Bits: A Groove Down Each Face of the Point Sharpens Its Cutting Edge (Robinson, 1957)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Divisible Flanged Shaft Collar: Two Halves Locked by Lugs, Bolted Through the Shaft in One of Three Hole Pairs (Obey, 1916)
por Forge
Trabajo en Metal
1
0
0
0
0
0
One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)
por Forge
Trabajo en Metal
0
0
0
0
0
0
Mostrando 24 de 2105