Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)
Forge

Creado por

Forge

4. noviembre 2026NO
9
0
0
2
0

Colander: a Tinplate Colander with Perforated Body and Bottom (Hasluck, 1907)

A tinsmith's colander for straining: a tapered tinplate body and a hollowed bottom, both punched full of holes, standing on a wired hoop, with two bow handles. The body pattern is a ring segment: outer radius = top diameter, inner radius = bottom diameter, which gives sides at 60 degrees. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 50-51. Unknown: sizes, solder. Picture: Figs. 126-127 of the book.
Intermedio
Unknown

Instrucciones

1

Set out the body pattern

Choose the top and bottom diameters. On tinplate, strike an arc with radius equal to the top diameter and, from the same centre, one equal to the bottom diameter (Fig. 127); the sides then slope at 60 degrees. Mark the rows of holes, add edges for a grooved seam and the wire, and cut it out.

Materiales para este paso:

Chapa de hojalataChapa de hojalata1 body

Herramientas necesarias:

Compás de puntasCompás de puntas
Punta de trazarPunta de trazar
Tijeras de chapaTijeras de chapa
2

Break, punch and planish the body

'Break' the pattern through the rollers, turning it the opposite way each pass, so it won't crease when bent. Punch the holes on a hardwood block, then flatten and planish the burrs.

Herramientas necesarias:

Cilindradora de chapaCilindradora de chapa
Sacabocados para chapaSacabocados para chapa
Bloque de madera duraBloque de madera dura
Martillo de aplanarMartillo de aplanar
3

Seam and wire the body

Set off the edges for a grooved seam, bend the body to shape and seam it. Solder the seam inside. Set off an edge on the wide end and wire it with No. 10 B.W.G. wire. If you like, raise a swage about 1 1/2 in below the wired edge: it stiffens the colander and looks better.

Materiales para este paso:

Alambre de hierroAlambre de hierro1 No. 10 B.W.G.
Estaño-plomo de soldaduraEstaño-plomo de soldadura1 seam

Herramientas necesarias:

Mazo de maderaMazo de madera
EstacaEstaca
Soldador eléctricoSoldador eléctrico
FundenteFundente
4

Make and fit the bottom

Cut out the bottom, hollow it and edge it to fit the small end. Inside, mark circles from 1 in across at the centre, each 1 in wider than the last, out to the edge. Punch holes at short intervals round them and flatten the burrs on an upturned hollowing hammer. Solder the bottom on.

Materiales para este paso:

Chapa de hojalataChapa de hojalata1 bottom
Estaño-plomo de soldaduraEstaño-plomo de soldadura1 bottom

Herramientas necesarias:

Compás de puntasCompás de puntas
Tijeras de chapaTijeras de chapa
Sacabocados para chapaSacabocados para chapa
Martillo de aplanarMartillo de aplanar
Soldador eléctricoSoldador eléctrico
FundenteFundente
5

Add the hoop and handles

Cut a strip 1 1/2 in wide, as long as the circumference of the bottom. Wire it with No. 10 B.W.G., round it, seam it and solder it on as the foot. Rivet a pair of bow handles opposite each other at the top.

Materiales para este paso:

Chapa de hojalataChapa de hojalata1 hoop
Alambre de hierroAlambre de hierro1 hoop
Estaño-plomo de soldaduraEstaño-plomo de soldadura1 hoop
MangoMango2 bow handles
Remaches de hierroRemaches de hierro1 number not given

Herramientas necesarias:

Tijeras de chapaTijeras de chapa
Soldador eléctricoSoldador eléctrico
FundenteFundente
Martillo de remacharMartillo de remachar
6

Clean and scald

Clean with turpentine and whiting, then polish with dry whiting. Before first use, steep it a short time in boiling water, as for any metal article for the kitchen.

Herramientas necesarias:

TrementinaTrementina
Carbonato de calcio (blanco de España)Carbonato de calcio (blanco de España)
AguaAgua

Materiales

5

Herramientas requeridas

15

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...