Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Twin-Crank Slide-Top Churn: Two Dashers on a Bent Crank Shaft, Sliding Plates Keep the Milk In
Cable L. Gilpatrick of Saco, Maine, received US 25,405, dated 13 September 1859, for a churn. A crank shaft bent into two opposite cranks rides on two posts above a box and works two dashers, so one goes down as the other comes up. Each dasher is two boards crossed and bored with holes. The staffs pass through holes in two slides that move in casings on the top, following the staffs so the milk cannot splash out.
The patent gives no sizes; every size here is ours.
Intermedio
About 2 days, plus printing
Instrucciones
1
1
One up, one down
One up, one down
Cargando el cuaderno de Jupyter…
2
2
Two dashers in one box, a few weeks before
Two dashers in one box, a few weeks before
Campbell rocked his two dashers on a lever. Gilpatrick drives his from a bent crank shaft and covers the top with slides.
3
3
Read US 25,405
Read US 25,405
"Motion is then communicated to the dashers by means of the crank-shaft. As one dasher descends, the other ascends. Thus the milk is kept in contant agitation, which is necessary in order to churn expeditiously. The slides being operated upon by the dasher-staffs prevents the milk from splashing out, as it otherwise would do."
4
4
Print the staff collars
Print the staff collars
Each collar is two halves round a crank pin: the lower half with a 30 mm square socket for the staff, and a cap; two M5 screws close them. Print two sets. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Box A and its posts
Box A and its posts
From 20 mm hardwood make a box 400 x 360 mm and 450 mm deep inside, with a bottom. Make the two 400 mm sides 170 mm taller, narrowed to posts 120 mm wide above the box, and bore each post 13 mm, 600 mm above the bottom's underside, for the shaft. Glue and screw a cleat 20 mm square along the inside of each post side, 30 mm below the rim, for the top. Fill the box with water overnight so it swells tight, then empty it.
Materiales para este paso:
Tabla de madera dura3 piezas
Cola de carpintero1 pieza
Tornillos para madera30 piezasHerramientas necesarias:
Sierra de mesa
Serrucho
Taladro inalámbrico
Juego de brocas
Sargento
Escuadra fija
Cinta métrica
Agua6
6
Crank shaft D and crank E
Crank shaft D and crank E
Cut 12 mm stainless rod about 750 mm long. Heat each bend red with the torch and bend it in the vise into two cranks of 50 mm throw, pointing opposite ways, each crank pin 50 mm long, their middles 180 mm apart. Check the journals line up by rolling the shaft on the bench. Thread one end through a post, the collars' lower halves onto the pins, and the other end through the other post. Fix a hardwood crank E, 160 mm long with a handle, on the end that sticks out.
Materiales para este paso:
Varilla de acero inoxidable1 piezaTabla de madera dura1 pieza
Espigas de madera dura1 piezaCola de carpintero1 piezaHerramientas necesarias:
Soplete de propano
Tornillo de banco
Martillo
Guantes resistentes al calor
Sierra para metales
Limas (lima de mano)Taladro inalámbricoJuego de brocasCinta métrica7
7
Top A', casings F and slides H
Top A', casings F and slides H
Cut the top to drop onto the cleats, with two slots 140 x 50 mm across it, under the cranks, and a finger hole. Over each slot build a casing F: two rails 20 x 26 mm, 370 mm long, 80 mm apart, with a strip on each that overhangs the inside by 8 mm, and an end block at each end, leaving 346 mm inside. Cut each slide H 240 x 79 mm from 18 mm hardwood, so it slides under the strips, with a hole 34 mm square in its middle, 4 mm bigger than the staff.
Materiales para este paso:
Tabla de madera dura2 piezasCola de carpintero1 piezaTornillos para madera24 piezasHerramientas necesarias:
Sierra de mesa
Fresadora de mano
Formón de mortaja
Mazo de maderaTaladro inalámbricoJuego de brocas
Papel de lijaSargento8
8
Staffs B and dashers C
Staffs B and dashers C
Cut two staffs 30 mm square, 480 mm long. For each dasher, half-lap two boards 180 x 50 x 15 mm into a cross, bore eight 12 mm holes, cut a 30 mm square hole in the middle, and glue the staff's end into it. Set the top on its cleats, pass each staff up through its slide's hole, and bolt the collar's cap over its pin and onto the staff's top, turning the cross so its arms point to the box's corners.
Materiales para este paso:
Tabla de madera dura1 piezaCola de carpintero1 pieza
Tornillos de máquina4 piezas
Arandela plana4 piezas
Tuerca autoblocante con inserto de nailon4 piezas
Filamento PETG1 piezaHerramientas necesarias:
Impresora 3D de filamento (FDM)Sierra de mesaFormón de mortajaMazo de maderaTaladro inalámbricoJuego de brocas
Juego de destornilladoresPapel de lija9
9
The build in 3D
The build in 3D
FreeCAD model of this build, one side and the lower part of one post cut away: the box, the bent crank shaft on its posts with crank E, the two staffs in their collars, the dashers, and the slides in their casings on the top. The crank was turned through 24 positions.
10
10
Churn
Churn
Lift the collars' caps off, take out the top, pour in about 15 litres of heavy cream at about 15 °C, checked with the thermometer, and put the top and caps back. Turn the crank steadily, timing it. When the butter comes, take the top out, lift out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Materiales para este paso:
Crema de leche espesa15 l
Sal marina gruesa1 piezaAgua1 piezaHerramientas necesarias:
Termómetro de sonda permanente
Cronómetro
Báscula digital de cocina
Bol grande de acero inoxidableJuego de destornilladores11
11
Troubleshooting
Troubleshooting
Twin-crank churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Cable L. Gilpatrick** of Saco, Maine, US 25,405, 13 September 1859, "Churn". He claimed the crank shaft D and staffs B with the top A', "when said top is provided with boxes (F,) in which play slides, through which the staffs pass". The patent gives no sizes; every size here is ours. His collars are not described beyond "passing around said cranks"; ours are printed and split so the top can come out.
Materiales
12- 3 piezasMarcador de posición
- 4 piezasMarcador de posición
- 54 piezasMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 4 piezasMarcador de posición
- 4 piezasMarcador de posición
- Marcador de posición
- 1 piezaMarcador de posición
- Marcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
Herramientas requeridas
24- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Archivos de diseño
2
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
Hinged-Float Double-Dasher Churn: Floats That Close Going Down and Fall Open Coming Up
por Buttercup
Carpintería
2
0
0
0
0
0
Star-Dasher Crank Churn: Geared Crank and Flywheel Drive Two Notched Dashers Set Point Over Gap
por Martin
Carpintería
4
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANÍA
60
0
0
0
0
0
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.