Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE

Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)
How the common English screw auger was made, from Holtzapffel's Turning and Mechanical Manipulation: a parallel steel blade twisted red-hot, a worm at the point to pull it into the wood, two lips sharpened to cut, and the shaft end forged into an eye for a tightly driven cross handle.
Avanzado
A day at the forge
Instrucciones
1
1
Twist count
Twist count
Cargando el cuaderno de Jupyter…
2
2
Read Holtzapffel
Read Holtzapffel
"The ordinary screw auger ... is forged as a parallel blade of steel ... it is twisted red-hot."
3
3
Forge the blade
Forge the blade
Draw a steel bar out into a flat, parallel blade, leaving a round end for the shaft. Width, thickness and length are ours: make the blade as wide as the hole you want.
Materiales para este paso:
Barra de acero de herramientas1 piezaHerramientas necesarias:
Fragua de herrero
Yunque
Martillo
Tenazas de herrero
Fuller (degolladera)4
4
Twist it red-hot
Twist it red-hot
Heat the blade to red, grip one end in the vice and twist the other with a wrench into an even double spiral. Twist in short heats and keep the pitch even.
Herramientas necesarias:
Fragua de herrero
Tornillo de banco
Volvedor de machos
Tenazas de herrero5
5
Form the worm and lips
Form the worm and lips
File the point into a worm (a small tapered screw, as on a gimlet) that pulls the auger into the work. Shape and sharpen the two corners, or lips, to cut at the very ends and a little up the sides.
Herramientas necesarias:
Tornillo de banco
Limas (lima de mano)6
6
Forge the eye
Forge the eye
Forge the top of the shaft into a ring or eye.
Herramientas necesarias:
Fragua de herrero
Yunque
Martillo
Tenazas de herrero7
7
Harden and temper (ours)
Harden and temper (ours)
He gives no hardening. Ours: harden the cutting end and temper it as for other wood-cutting edge tools, then hone the lips.
Herramientas necesarias:
Fragua de herrero
Cubo de temple
Piedra de afilar8
8
Fit the cross handle
Fit the cross handle
Shape a hardwood bar and drive it tightly through the eye as a transverse handle.
Materiales para este paso:
Tabla de madera dura1 piezaHerramientas necesarias:
Cuchilla de dos mangos
Martillo9
9
Troubleshooting
Troubleshooting
Screw auger troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From Charles Holtzapffel, **Turning and Mechanical Manipulation**, vol. II (1846), pp. 540, 543 and 545-546 (checked on the archive.org scan turningmechanica02holtuoft). He also describes the single-lip auger: a half-round bar coiled into an open spiral with the flat side outwards, the end shaped like a shell auger. He gives no sizes or heat treatment: those, the tools and the handle wood are ours.
Materiales
2- Marcador de posición
- 1 piezaMarcador de posición
Herramientas requeridas
11- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.



