ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes
The bee skep is the coiled-straw beehive that housed honeybees across Europe for roughly two thousand years, from antiquity into the 1800s, before wooden box hives replaced it. Using the same coiling technique as a straw basket, long rye straw is wound into a dome and stitched together with split cane. This blueprint builds a traditional skep by hand — from preparing the straw to the finished, weatherproofed hive ready to house a swarm.
Intermedio
8
Instrucciones
1
1
Harvest and clean long rye straw
Harvest and clean long rye straw
Cut long rye or wheat straw and strip off the seed heads and leaf sheaths, keeping the hollow stems long and unbroken for strong coils.
Materiales para este paso:
Paja de centeno1 manojoHerramientas necesarias:
Cuchillo2
2
Split and soak the binding cane
Split and soak the binding cane
Split lengths of cane into thin flexible strips and soak them in water until pliable — these will sew the straw coils together.
Materiales para este paso:
Caña partida1 manojo
Agua3 litrosHerramientas necesarias:
Cuchillo3
3
Make the girth gauge
Make the girth gauge
Form a small open ring about 2.5 cm across (the traditional 'girth', often a cow-horn tip). Straw fed through it keeps every coil the same thickness.
Herramientas necesarias:
Calibre de contorno para colmena de paja4
4
Bind the crown
Bind the crown
Take a small handful of straw, bend it into a tight knot to form the top knob of the skep, and lash it firmly with a strip of split cane.
Materiales para este paso:
Paja de centeno1 manojoCaña partida1 metroHerramientas necesarias:
Punzón (lezna)5
5
Feed straw into an even rope
Feed straw into an even rope
Pass straw through the girth to form a continuous rope of even thickness, adding a few stems at a time so the bundle never thins as you work.
Materiales para este paso:
Paja de centeno1 manojoHerramientas necesarias:
Calibre de contorno para colmena de paja6
6
Sew the first coils to the crown
Sew the first coils to the crown
Coil the straw rope in a tight spiral around the crown. Push the awl through the coil below, pass split cane through, and pull each stitch snug about every 2 cm.
Materiales para este paso:
Caña partida1 metroHerramientas necesarias:
Punzón (lezna)7
7
Spiral outward to start the dome
Spiral outward to start the dome
Continue spiralling outward from the crown, binding each new coil to the one below. The domed top of the hive begins to take shape.
Materiales para este paso:
Paja de centeno1 manojoCaña partida1 metroHerramientas necesarias:
Punzón (lezna)8
8
Build the domed wall downward
Build the domed wall downward
Work the spiral down and out to build the wall, keeping the girth on the rope to hold thickness and every binding stitch tight and evenly spaced.
Materiales para este paso:
Paja de centeno1 manojoCaña partida1 metroHerramientas necesarias:
Punzón (lezna)Calibre de contorno para colmena de paja9
9
Keep the courses even
Keep the courses even
Control how far each coil steps outward so the dome stays smooth and symmetrical. Steady, even courses make a strong, weathertight hive.
Materiales para este paso:
Paja de centeno1 manojoHerramientas necesarias:
Punzón (lezna)10
10
Widen to the finished base
Widen to the finished base
As you near the bottom, let the coils reach the finished diameter of about 35–40 cm — the standard size for a colony of bees.
Materiales para este paso:
Paja de centeno1 manojoCaña partida1 metroHerramientas necesarias:
Punzón (lezna)11
11
Cut the flight entrance
Cut the flight entrance
At the lower edge, cut a small entrance notch in a coil so the bees can come and go once the skep is set open-side down.
Herramientas necesarias:
Cuchillo12
12
Finish and lock the base coil
Finish and lock the base coil
Complete the last coil at the base, taper off the straw rope, and lock the final binding stitches so the skep cannot unravel.
Materiales para este paso:
Caña partida1 metroHerramientas necesarias:
Punzón (lezna)13
13
Trim the skep clean
Trim the skep clean
Trim protruding straw ends and stray cane with the knife to leave a clean rim and an even outer surface.
Herramientas necesarias:
Cuchillo14
14
Clom the outside for weatherproofing
Clom the outside for weatherproofing
Smear a thin coat of cow-dung-and-clay daub over the straw to shed rain and seal drafts, then let it dry — the traditional 'clomming'.
Materiales para este paso:
Boñiga de vaca2 kg
Arcilla de bola1 kg15
15
Cure the finished skep
Cure the finished skep
Cure the skep in a dry, airy place. Once fully dry it is ready to hive a swarm — set open-side down on a board or stand.
Materiales
5- 1 manojoMarcador de posición
- 1 metroMarcador de posición
- 3 litrosMarcador de posición
- 2 kgMarcador de posición
- 1 kgMarcador de posición
Materiales de Blueprints conectados
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
Building a Thatched Lean-To Shelter — Basic Wind and Rain Protection
por Spartan
Naturaleza Salvaje
50
0
0
0
1
0
Egyptian Beeswax Candle — Making Beeswax Candles with Rush Wicks
por YourGrandma
Biología
73
0
0
0
1
0
Honey as a Wound Dressing — The Oldest Antimicrobial Medicine Known to Humanity
por Bob
Naturaleza Salvaje
56
0
0
0
3
0
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.