Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)
Forge

Creado por

Forge

4. noviembre 2026NO
22
0
0
0
0

Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)

The file for sharpening saw teeth as Sheffield made it by hand: a three-square (triangular) bar of cast steel, not tapering, forged in a V-shaped boss, its teeth cut one by one with a chisel and hammer, then hardened under a coat of animal carbon and salt and quenched in cold spring water. Ure says saw files in particular should be hardened with the carbon mixture, so they will cut iron and steel. Not given: sizes and teeth per inch. Source: A. Ure, Dictionary of Arts, Manufactures, and Mines (1839), File. Picture: our drawing.
Avanzado
Unknown

Instrucciones

1

Forge the blank

Draw cast steel out square at the forge, then lay it with one angle down in a boss whose recess has two sides meeting at an angle, so the hammer forms one side and the boss the other two. Keep it the same size along its length (saw files are not tapered).

Materiales para este paso:

Acero al crisolAcero al crisol1 cast steel bar
Dimensiones desconocidasDimensiones desconocidas1 pieza

Herramientas necesarias:

Fragua de herreroFragua de herrero
Tenazas de fraguaTenazas de fragua
Estampa inferiorEstampa inferior
MartilloMartillo
Mazo pesadoMazo pesado
2

Cut the teeth

On an anvil with a flat, even face, hold the file down with a leather strap over each end, the workman's feet in the straps like stirrups. Cut the teeth with a chisel a little broader than the file, sharpened to about 20 degrees, struck with a hammer of 1 to 6 lb. For single cut, run a fine file lightly over the teeth to take off the roughness; for double cut, cut a second set nearly at right angles to the first.

Herramientas necesarias:

Yunque de aceroYunque de acero
Correa de cueroCorrea de cuero
CortafríosCortafríos
MartilloMartillo
Lima para metalLima para metal
3

Cut the other sides

To cut the next side, lay the file in a piece of lead-tin alloy with an angular groove, so the teeth already cut are not spoiled on the anvil.

Herramientas necesarias:

Estaño-plomo de soldaduraEstaño-plomo de soldadura
Yunque de aceroYunque de acero
CortafríosCortafríos
MartilloMartillo
4

Coat for hardening

Distil shoemakers' and curriers' leather refuse in an iron still and powder the bright coal left. Grind about equal parts by bulk of this carbon and salt to the consistence of cream with water and cover the file with it.

Herramientas necesarias:

Retorta de hierroRetorta de hierro
SalSal
AguaAgua
5

Harden

Hold the file by the tang in a fire of very small cokes, drawing it out often, until it is an even cherry red from tang to point. Plunge it straight down, quickly, into clear spring water as cold as possible.

Herramientas necesarias:

Fragua de herreroFragua de herrero
Coque metalúrgicoCoque metalúrgico
Tenazas de fraguaTenazas de fragua
AguaAgua
6

Clean and oil

Brush the file with water and powdered cokes until clean and metallic, wash it in two or three waters to take off all the salt, dip it in lime-water, dry it quickly before the fire and oil it while warm with olive oil containing a little oil of turpentine.

Herramientas necesarias:

Coque metalúrgicoCoque metalúrgico
AguaAgua
Agua de calAgua de cal
Aceite de olivaAceite de oliva
TrementinaTrementina

Materiales

2

Herramientas requeridas

17

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...