ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Using a Piezo Buzzer — SIK Circuit 11
Ed

Creado por

Ed

17. marzo 2026FI
99
0
0
0
0

Using a Piezo Buzzer — SIK Circuit 11

Play a song with a piezo buzzer! Learn about the tone() function, musical frequencies, arrays for storing melodies, and how to create your own tunes.

Instrucciones

1

Parts & Introduction

A piezo buzzer converts electrical signals into sound. Using Arduino's built-in tone() function, you can play specific musical frequencies. This sketch plays a simple melody using character arrays for notes and integer arrays for timing.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 1x Piezo Buzzer
  • 3x Jumper Wires

Note Frequency Reference

NoteFreq
c262 Hz
d294 Hz
e330 Hz
f349 Hz
g392 Hz
a440 Hz
b494 Hz
C523 Hz

Materiales para este paso:

SparkFun Inventor's Kit - V3.2SparkFun Inventor's Kit - V3.21 kit

Herramientas necesarias:

Ordenador con el IDE de ArduinoOrdenador con el IDE de Arduino
2

Hardware Hookup

Wiring Instructions

  1. Place the piezo buzzer in the breadboard. It has two pins — one marked with "+".
  2. Connect the positive pin (+) to Arduino Digital Pin 9 (PWM).
  3. Connect the negative pin to GND.

Tip: If the buzzer doesn't fit easily, try rotating it slightly to align with diagonal breadboard holes.

Materiales para este paso:

Zumbador piezoeléctricoZumbador piezoeléctrico1 pieza
Placa de pruebasPlaca de pruebas1 pieza
Cables de puenteCables de puente2 piezas
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

piezo_buzzer.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 11 — BUZZER

Use the buzzer to play a song!

Hardware connections:
  Buzzer positive pin (+) to digital pin 9 (PWM)
  Buzzer negative pin to GND

This code is completely free for any use.
*/

const int buzzerPin = 9;

const int songLength = 18;

char notes[] = "cdfda ag cdfdg gf ";  // space = rest

int beats[] = {1,1,1,1,1,1,4,4,2,1,1,1,1,1,1,4,4,2};

int tempo = 113;

void setup()
{
  pinMode(buzzerPin, OUTPUT);
}

void loop()
{
  int i, duration;

  for (i = 0; i < songLength; i++)
  {
    duration = beats[i] * tempo;

    if (notes[i] == ' ')
    {
      delay(duration);
    }
    else
    {
      tone(buzzerPin, frequency(notes[i]), duration);
      delay(duration);
    }
    delay(tempo/10);
  }

  while(true){}  // Play once, then stop. Remove this line to loop.
}

int frequency(char note)
{
  int i;
  const int numNotes = 8;

  char names[] = { 'c', 'd', 'e', 'f', 'g', 'a', 'b', 'C' };
  int frequencies[] = {262, 294, 330, 349, 392, 440, 494, 523};

  for (i = 0; i < numNotes; i++)
  {
    if (names[i] == note)
    {
      return(frequencies[i]);
    }
  }
  return(0);
}

Materiales para este paso:

Arduino Uno R3Arduino Uno R31 pieza

Herramientas necesarias:

Ordenador con el IDE de ArduinoOrdenador con el IDE de Arduino
4

Test & Experiment

What You Should See

You won't see anything — but you'll hear a melody playing from the buzzer! The song plays once and stops.

Troubleshooting

  • No sound: The buzzer pins are easy to misplace on the breadboard. Double-check placement and make sure both pins have good contact.
  • Want it to stop: Pull the buzzer out while working on other things, plug it back in to test.

Experiments to Try

  • Remove the while(true){} line to make the song loop continuously.
  • Write your own melody by changing the notes[] and beats[] arrays.
  • Add more notes by expanding the frequency() function with sharps and flats.
  • Use a button (from Circuit 5) to trigger the melody on demand.

Materiales

5

Herramientas requeridas

1
Total estimado
Lo que compró quien lo hizo. Los materiales sin precio se consiguen donde tú los compres.
€95.47

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...