ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Silver Solder from Fine Silver, Copper and Spelter: Gee, 1877
Silver solder joins silver, copper and brass with a strong, hard seam. The silversmith George Gee preferred one made of fine silver, shot copper and a little spelter (zinc), melted only once: his best hard solder is 16 dwt of fine silver, 3 dwt 12 gr of shot copper and 12 gr of spelter to the ounce, about 80, 17.5 and 2.5 per cent. More copper and zinc make it flow sooner (his medium, easy and common solders). Silver and copper alone give the hardest, least fusible solder; too much zinc makes it eat away during soldering.
Intermedio
Two hours
Instrucciones
1
1
Weigh the metals
Weigh the metals
Cargando el cuaderno de Jupyter…
Materiales para este paso:
Plata fina80 g
Lingote de cobre17.5 g
Lingote de zinc2.5 gHerramientas necesarias:
Báscula
Cortafríos2
2
Anneal and test the crucible
Anneal and test the crucible
Before a new plumbago (graphite) crucible is charged, heat it slowly to redness on a fire that is dying down and has no blaze, so it does not crack. Touch it with a cold iron bar: if cracks show, reject it.
Herramientas necesarias:
Crisol de grafito y arcilla
Horno de carbón vegetal
Tenazas para crisol3
3
Melt silver and copper
Melt silver and copper
Put the copper at the bottom of the crucible, the silver on top, and melt them in the furnace. Stir them well together with an iron stirrer, tapered at the point and first heated to redness. When the metals are just beginning to fuse, cover the melt with finely divided, pure charcoal to keep the air off it.
Materiales para este paso:
Carbón vegetal - molido fino1 as requiredHerramientas necesarias:
Horno de carbón vegetal
Agitador de hierro
Guantes resistentes al calor4
4
Add the spelter
Add the spelter
Hold the spelter in a long pair of tongs over the mouth of the crucible, inside the furnace, until it has almost reached its melting point, then drop it into the molten metal and stir quickly so it mixes in. Zinc burns away quickly in the air, so it goes in last.
Herramientas necesarias:
TenazasAgitador de hierroGuantes resistentes al calor5
5
Pour the ingot
Pour the ingot
Withdraw the crucible from the furnace at once and pour into an ingot mould that is clean, smooth, lightly greased, dusted with fine charcoal and warmed: a cold mould makes the metal spout, but do not overheat it either. Melt solder only once; Gee found that solders containing volatile metals grow hard, brittle and drossy with repeated melting.
Materiales para este paso:
Carbón vegetal - molido fino1 as requiredHerramientas necesarias:
Tenazas para crisol
LingoteraGuantes resistentes al calor6
6
Roll into pallions or file to dust
Roll into pallions or file to dust
Roll the solder out thin between flattening rollers and cut it lengthways and then crossways with hand shears into little bits (pallions), or file it into fine dust, according to the work in hand. The work is then bound together, wetted with a paste of borax and water, and the pallions laid on the joints and melted with a blowpipe flame.
Herramientas necesarias:
Laminador
Tijeras para metal
Limas (lima de mano)Materiales
4- 80 gMarcador de posición
- 17.5 gMarcador de posición
- 2.5 gMarcador de posición
- 1 as requiredMarcador de posición
Herramientas requeridas
12- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
Peligroso
Extracting Silver by Cupellation — Separating Noble Metal from Lead Ore
por Peter
Trabajo en Metal
71
0
0
0
2
0
Smelting Copper from Malachite — From Green Ore to Red Metal
por Peter
Trabajo en Metal
108
0
0
0
10
0
Extracting Zinc from Sphalerite — Roasting and Reduction of the Invisible Metal
por Peter
Trabajo en Metal
81
0
0
0
8
0
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.