Colaboración
ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Youblob · CC0
55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)
The open-top 55-gallon (208-litre) steel drum, built to the rule US railways and shippers used for single-trip removable-head drums: welded low-carbon steel body, three rolled hoops, a crowned bottom, and a lid clamped by a bolted ring over a gasket.
Source: ICC Specification 17H, 49 CFR 78.118, Federal Register, 29 December 1964. The spec does not say how the bottom is joined. The litre figure, the gasket rubber and the machines are ours. Picture drawn by Youblob.
Avanzado
Production line
Instrucciones
1
1
Cut low-carbon steel sheets
Cut low-carbon steel sheets
Use low-carbon steel for body and heads. For a 55-gallon drum: body 18 gauge, bottom head 18 gauge, removable head 14 gauge (16 gauge if the cover has one or more corrugations near its edge). 18 gauge is 0.0478 in nominal and at least 0.0428 in; 14 gauge 0.0747 in and at least 0.0677 in, measured at least 3/8 in from an edge.
Materiales para este paso:
Chapa de acero dulce1 body, bottom and lid sheetsHerramientas necesarias:
Tijeras de chapa para trabajo pesado
Micrómetro2
2
Roll and weld the body
Roll and weld the body
Roll the body sheet into a cylinder and weld the seam. The body seam must be welded.
Herramientas necesarias:
Cilindradora de chapa
Soldadora de costura de tubos3
3
Roll in three hoops
Roll in three hoops
Roll or swage three hoops into the body, one of them near the top curl.
Herramientas necesarias:
Rodillos de acordonar4
4
Press crowned heads
Press crowned heads
Press the bottom head crowned (convex) by at least 3/8 in, not standing out beyond the level of the chime, and fit it to the body. The spec does not say how the bottom is joined.
Herramientas necesarias:
Prensa de estampación5
5
Make the bolted ring and gasket
Make the bolted ring and gasket
Make the closing ring from 12-gauge steel with drop-forged lugs, one of them threaded, and a 5/8 in bolt and nut (for drums over 30 gallons). Fit a gasket under the lid: gaskets are required.
Materiales para este paso:
Chapa de acero dulce1 12-gauge strip for the ring
Barra redonda de acero dulce1 for the lugs
Surtido de tornillos hexagonales1 5/8 in bolt
Tuerca hexagonal1 5/8 in
Plancha de caucho1 gasketHerramientas necesarias:
Cilindradora de chapa
Martinete de caída con matrices de forja
Cúter de precisión6
6
Check capacity and mark
Check capacity and mark
The drum must hold at least 4 % more than its marked 55 gallons, and no more than 5 % more (or 4 % plus 1 quart, whichever is greater). Emboss the marks: ICC-17H, STC (single-trip container), the maker, and the gauges, capacity and year.
Herramientas necesarias:
Prensa de estampación7
7
Leak-test every drum
Leak-test every drum
Test each drum by air pressure inside of at least 7 psi with its seams under water or covered with soapsuds or heavy oil. Reject leakers, or repair them the way they were made and test again.
Materiales para este paso:
Agua1 as requiredHerramientas necesarias:
Compresor de aire
Manómetro8
8
Type tests every four months
Type tests every four months
On drums taken at random and closed as for use: drop one filled with water to 98 % from 4 ft onto concrete so it lands diagonally on the chime, and hold another at 15 psi water pressure for 5 minutes. None may leak.
Materiales para este paso:
Agua1 as requiredHerramientas necesarias:
ManómetroMateriales
6- 1 12-gauge strip for the ringMarcador de posición
- 1 for the lugsMarcador de posición
- 1 5/8 in boltMarcador de posición
- 1 5/8 inMarcador de posición
- 1 gasketMarcador de posición
- 2 as requiredMarcador de posición
Herramientas requeridas
10- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
Este plano hace
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.