ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
Martin

Creado por

Martin

30. septiembre 2026NO
42
0
0
0
0

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It

A plunger pressed straight down by the hand needs a strong push to empty a lemon. A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger." This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
Intermedio
About 5 hours

Instrucciones

1

The cam's force

Cargando el cuaderno de Jupyter…
2

A lever press before it

The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3

Read US 165,638

"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E." "When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4

Build the squeezer and press lemons

**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole. **Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl. **Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin. **Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised. **Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.

Materiales para este paso:

Tabla de madera duraTabla de madera dura2 piezas
Bloque de madera duraBloque de madera dura2 piezas
Espiga de maderaEspiga de madera0.6 metro
Tornillos para maderaTornillos para madera16 piezas
Cola de carpinteroCola de carpintero1 pieza
LataLata1 pieza
Bisagra de libroBisagra de libro1 pieza
Redondo de acero dulceRedondo de acero dulce0.2 metro
ClavosClavos2 piezas
Muelle de tracciónMuelle de tracción2 piezas
LimónLimón3 piezas

Herramientas necesarias:

SerruchoSerrucho
Juego de formones para maderaJuego de formones para madera
EscofinaEscofina
Taladro inalámbricoTaladro inalámbrico
Juego de brocasJuego de brocas
Tijeras de chapaTijeras de chapa
MartilloMartillo
Juego de destornilladoresJuego de destornilladores
Sierra para metalesSierra para metales
Cuchillo de cocinaCuchillo de cocina
Báscula digital de cocinaBáscula digital de cocina
Guantes de trabajo de cueroGuantes de trabajo de cuero
5

A cam that slips, jams or does not lift

Cam-lever lemon squeezer troubleshooting.

Flow

Loading...
6

History and honest limits

**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever. **Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.

Materiales

11

Herramientas requeridas

12

CC0 Dominio público

Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.

Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.

Discusión

(0)

Iniciar sesión para unirte a la discusión

Cargando comentarios...