ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
The Hinged-Hook Can Opener: A Lever That Hooks Under the Far Side
The cover of a Lyman fruit can is hard to lift, and devices to ease it were not purely mechanical.
S. O. Church of West Meriden, Connecticut, received US 61,161, dated 15 January 1867, for a can opener made of "a peculiarly formed lever": one end turned down and spread as a fulcrum on the cover's flange, the other a handle, and between them a hinged hook that takes the flange on the opposite side, set by a thumb on its arm, so that raising the handle draws the cover off.
This rung works out the pull on the flange, then builds the lever and hook from flat bar and lifts a sealed jar lid with it.
Intermedio
About 3 hours
Instrucciones
1
1
Pull on the flange
Pull on the flange
Cargando el cuaderno de Jupyter…
2
2
The sealed can before it
The sealed can before it
The embedded blueprint seals food by heat. Church's lever opens a sealed cover without prising at it.
3
3
Read US 61,161
Read US 61,161
"My invention, which fully overcomes the difficulty, is purely mechanical, and consists in a peculiarly formed lever, constructed so that one end forms the fulcrum to bear upon the upper side of the flange of the cover, while the other end forms a handle, and between which and the fulcrum is hinged a hook which takes hold beneath the flange of the cover upon the opposite side to the fulcrum, so that by raising the handle the cover is easily removed from the can."
4
4
Make the lever
Make the lever
Cut 200 mm of 25 × 3 mm flat bar. Bend the last 25 mm down at right angles and screw a 40 mm cross-piece of the bar under it: the spread fulcrum.
Materiales para este paso:
Pletina de acero dulce1 pieza
Tornillos de máquina1 pieza
Tuerca hexagonal1 piezaHerramientas necesarias:
Sierra para metales
Tornillo de banco
Martillo
Taladro inalámbrico
Juego de brocas
Llave inglesa ajustable
Guantes de trabajo de cuero5
5
Make the hook
Make the hook
Cut 60 mm of the bar, narrow it to 20 mm, and bend its foot inward 10 mm as the flange. Bend a short arm up from its top for the thumb.
Materiales para este paso:
Pletina de acero dulce1 piezaHerramientas necesarias:
Sierra para metales
Limas (lima de mano)Tornillo de bancoMartillo6
6
Hinge the hook
Hinge the hook
Drill the hook and the lever 5 mm, 60 mm from the fulcrum, and join them with an M5 screw, two washers and a nut left just slack.
Materiales para este paso:
Tornillos de máquina1 pieza
Arandela plana1 piezaTuerca hexagonal1 piezaHerramientas necesarias:
GraneteTaladro inalámbricoJuego de brocas
Juego de destornilladoresLlave inglesa ajustable
Gafas de seguridad transparentes7
7
The patent drawing
The patent drawing
US 61,161 drawing sheet, public domain (expired patent).
8
8
Seal a jar and lift its lid
Seal a jar and lift its lid
Fill a Mason jar with water from the kettle at the boil, put on a new flat lid, screw the band on and let it cool for two hours so the lid pulls down. Then remove the band. Rest the fulcrum on one side of the lid, thumb the hook under the opposite edge, and lift the handle with the force meter; note the force.
Materiales para este paso:
Tarros de conserva (Mason)1 pieza
Agua1 piezaHerramientas necesarias:
Hervidor de fogón
Dinamómetro (balanza de resorte)
Guantes resistentes al calor9
9
A hook that slips, binds or bends
A hook that slips, binds or bends
Hinged-hook can opener troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**S. O. Church** of West Meriden, Connecticut, assignor to himself and S. S. Wilcox, received US 61,161, dated 15 January 1867. It was designed for the "Lyman Patent Fruit Can" but applies to other cans of similar construction. The hook is spread and curved, with a flange projecting inward; it uses the flange that is formed on the cover's lower edge when the cover is "struck up." His claim covers the lever with its fulcrum, the hook and the handle.
**Honest limits.** A Mason jar's flat lid stands in for Lyman's cover, and screws for his pivot. Your forces are the result.
Materiales
6- 1 piezaMarcador de posición
- 2 piezasMarcador de posición
- 2 piezasMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
Herramientas requeridas
14- Marcador de posición
- Marcador de posición
- Marcador de posición
- 1 vendor sell this, none ship to you yetMarcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.